HPQ-3.3/50-D48N-C Murata Power Solutions Inc, HPQ-3.3/50-D48N-C Datasheet - Page 6

• Manufacturer Part Number: HPQ-3.3/50-D48N-C
• Description: CONV DC/DC 1/4 BRICK 3.3V 165W
• Manufacturer: Murata Power Solutions Inc
• Series: HPQ-3.3/50-D48r
• Type: Isolated with Remote On/Off and UVLOr

Specifications of HPQ-3.3/50-D48N-C

• Output: 3.3V
• Number Of Outputs: 1
• Power (watts): 165W
• Mounting Type: Through Hole
• Voltage - Input: 36 ~ 75V
• Package / Case: 8-DIP Module, 1/4 Brick
• 1st Output: 3.3 VDC @ 50A
• Size / Dimension: 2.30" L x 1.45" W x 0.40" H (58.4mm x 36.8mm x 10.2mm)
• Operating Temperature: -40°C ~ 85°C
• Power (watts) - Rated: 165W
• Efficiency: 90%
• Approvals: CSA, cUL, EN, IEC, UL
• Output Power: 165 W
• Input Voltage Range: 36 V to 75 V
• Output Voltage (channel 1): 3.3 V
• Output Current (channel 1): 50 A
• Isolation Voltage: 2.25 KV
• Product: Isolated
• Input Voltage (nominal): 48 V
• Package / Case Size: C61
• Output Type: Isolated
• Output Voltage: 3.3 V
• Dc / Dc Converter O/p Type: Quarter-Brick
• No. Of Outputs: 1
• Input Voltage: 36V To 75V
• Power Rating: 165W
• Output Current: 50A
• Approval Bodies: CSA / EN / UL
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 811-2249

Removal of Soldered Converters from Printed Circuit Boards
Should removal of the converter from its soldered connection be needed,
thoroughly de-solder the pins using solder wicks or de-soldering tools. At no
time should any prying or leverage be used to remove converters that have not
been properly de-soldered fi rst.
Input Source Impedance
These converters must be driven from a low ac-impedance input source. The
DC/DC’s performance and stability can be compromised by the use of highly
inductive source impedances. The input circuit shown in Figure 2 is a practical
solution that can be used to minimize the effects of inductance in the input
traces. For optimum performance, components should be mounted close to the
DC/DC converter.
I/O Filtering, Input Ripple Current, and Output Noise
All models in this Series are tested/specifi ed for input ripple current (also called
input refl ected ripple current) and output noise using the circuits and layout
shown in Figures 2 and 3. External input capacitors (C
primarily as energy-storage elements.
They should be selected for bulk capacitance (at appropriate frequencies),
low ESR, and high rms-ripple-current ratings. The switching nature of DC/DC
converters requires that dc voltage sources have low ac impedance as highly
inductive source impedance can affect system stability. In Figure 2, C
L
necessitate additional considerations.
In critical applications, output ripple/noise (also referred to as periodic and ran-
dom deviations or PARD) can be reduced below specifi ed limits using fi ltering
techniques, the simplest of which is the installation of additional external out-
put capacitors. Output capacitors function as true fi lter elements and should be
selected for bulk capacitance, low ESR, and appropriate frequency response.
In Figure 3, the two copper strips simulate real-world pcb impedances between
the power supply and its load. Scope measurements should be made using
BNC connectors or the probe ground should be less than ½ inch and soldered
directly to the test circuit.
All external capacitors should have appropriate voltage ratings and be located
as close to the converter as possible. Temperature variations for all relevant
parameters should be taken into consideration.
BUS
Technical Notes
simulate a typical dc voltage bus. Your specifi c system confi guration may
V
OSCILLOSCOPE
IN
+
–
See specs for component values.
TO
Figure 2. Measuring Input Ripple Current
C
BUS
L
BUS
CURRENT
PROBE
C
IN
3
1
+INPUT
–INPUT
IN
in Figure 2) serve
www.murata-ps.com
BUS
and
Isolated High Power Quarter Brick DC/DC Converters
The most effective combination of external I/O capacitors will be a function
of line voltage and source impedance, as well as particular load and layout
conditions.
Start-Up Threshold and Undervoltage Shutdown
Under normal start-up conditions, these converters will not begin to regulate
properly until the ramping input voltage exceeds the Start-Up Threshold. Once
operating, devices will turn off when the applied voltage drops below the Und-
ervoltage Shutdown point. Devices will remain off as long as the undervoltage
condition continues. Units will automatically re-start when the applied voltage
is brought back above the Start-Up Threshold. The hysteresis built into this
function avoids an indeterminate on/off condition at a single input voltage. See
Performance/Functional Specifi cations table for actual limits.
Start-Up Time
The V
ramping input voltage crosses the Start-Up Threshold voltage and the point at
which the fully loaded output voltage enters and remains within its specifi ed
regulation band. Actual measured times will vary with input source imped-
ance, external input capacitance, and the slew rate and fi nal value of the input
voltage as it appears to the converter. The On/Off to V
that the converter is turned off via the Remote On/Off Control with the nominal
input voltage already applied.
On/Off Control
The primary-side, Remote On/Off Control function can be specifi ed to operate
with either positive or negative polarity. Positive-polarity devices ("P" suffi x)
are enabled when the on/off pin is left open or is pulled high. Positive-polarity
devices are disabled when the on/off pin is pulled low (with respect to –Input).
Negative-polarity devices are off when the on/off pin is high and on when the
on/off pin is pulled low. See Figure 4.
Dynamic control of the remote on/off function is best accomplished with a me-
chanical relay or an open-collector/open-drain drive circuit (optically isolated if
appropriate). The drive circuit should be able to sink appropriate current (see
Performance Specifi cations) when activated and withstand appropriate voltage
when deactivated.
IN
to V
+OUTPUT
–OUTPUT
OUT
+SENSE
–SENSE
Figure 3. Measuring Output Ripple/Noise (PARD)
Start-Up Time is the interval between the point at which a
21 Feb 2011 MDC_HPQ-3.3/50-D48 Series.A13 Page 6 of 10
HPQ-3.3/50-D48 Series
C1 = 1μF CERAMIC
C2 = 10μF TANTALUM
LOAD 2-3 INCHES (51-76mm) FROM MODULE
7
8
4
5
C1
COPPER STRIP
COPPER STRIP
C2
email: [e-mail]
SCOPE
OUT
start-up time assumes
R
LOAD