SP706SEN-L Exar Corporation, SP706SEN-L Datasheet - Page 12

• Manufacturer Part Number: SP706SEN-L
• Description: IC SUPERVISOR MPU LP 8NSOIC
• Manufacturer: Exar Corporation
• Type: Simple Reset/Power-On Resetr

Specifications of SP706SEN-L

• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Number Of Voltages Monitored: 1
• Reset: Active Low
• Reset Timeout: 140 ms Minimum
• Voltage - Threshold: 2.93V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Chip Enable Signals: No
• Internal Hysteresis: Yes
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 1 V to 5.5 V
• Operating Temperature Range: - 40 C to + 85 C
• Output Type: Active Low
• Power Fail Detection: Yes
• Monitored Voltage: 2.93 V
• Undervoltage Threshold: 0.6 V
• Overvoltage Threshold: 3.85 V
• Manual Reset: Resettable
• Watchdog: Yes
• Battery Backup Switching: No
• Power-up Reset Delay (typ): 200 ms
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1 V
• Supply Current (typ): 25 uA
• Maximum Power Dissipation: 727 mW
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1229-5

Ensuring a Valid RESET Output Down to
V
When V
longer sinks current, it becomes an open circuit.
High-impedance CMOS logic inputs can drift to
undetermined voltages if left undriven. If a pull-
down resistor is added to the RESET pin, any
stray charge or leakage currents will be shunted
to ground, holding RESET LOW. The resistor
value is not critical. It should be about 100KΩ,
large enough not to load RESET and small
enough to pull RESET to ground.
Monitoring Voltages Other Than the
Unregulated DC Input
Monitor voltages other than the unregulated DC
by connecting a voltage divider to PFI and
adjusting the ratio appropriately. If required,
add hysteresis by connecting a resistor (with a
value approximately 10 times the sum of the
two resistors in the potential divider network)
between PFI and PFO. A capacitor between PFI
and GND will reduce the power-fail circuit's
sensitivity to high-frequency noise on the
line being monitored. RESET can be used to
monitor voltages other than the +3.3V/+3.0V
Figure 16. Typical Operating Circuit
Date: 6-28-04
CC
= 0V
µP
V
GND
CC
CC
falls below 1V, the RESET output no
I/O LINE
RESET
INTERRUPT
NMI
Regulated +3.3V/+3.0V
Power Supply
RESET
PUSHBUTTON
0.1µF
WDO
PFO
PFI
SWITCH
GND
V
Unregulated DC
SP706 +3.0/ +3.3 Low Power Microprocessor Circuits
CC
Power Supply
PFI
MR
R
R
1
2
12
V
RESET pulse when PFI drops below 1.25V.
Figure 17 shows the SP706R/S/T-SP708R/
S/T series configured to assert RESET when the
+3.3V/+3.0V supply falls below the RESET
threshold, or when the +12V supply falls below
approximately 11V.
Monitoring a Negative Voltage Supply
The power-fail comparator can also monitor a
negative supply rail, shown in Figure 18.
When the negative rail is good (a negative
voltage of large magnitude), PFO is LOW. By
adding the resistors and transistor as shown, a
HIGH PFO triggers RESET. As long as PFO
remains HIGH, the SP706P/R/S/T-SP708R/S/
T series will keep RESET asserted (where
RESET = LOW and RESET = HIGH). Note that
this circuit's accuracy depends on the PFI
threshold tolerance, the V
tors.
Interfacing to mPs with Bidirectional
RESET Pins
µPs with bidirectional RESET pins, such as the
Motorola 68HC11 series, can contend with the
RESET output. If, for example, the RESET
Figure 17. Monitoring Both +3.3V/+3.0V and +12V
Power Supplies
CC
to µP
line. Connect PFO to MR to initiate a
RESET
PFO
MR
+3.3V/+3.0V
© Copyright 2004 Sipex Corporation
CC
V
GND
CC
line, and the resis-
PFI
+12V
1MΩ
1%
130KΩ
1%