ADE7761AARS-RL Analog Devices Inc, ADE7761AARS-RL Datasheet
ADE7761AARS-RL
Specifications of ADE7761AARS-RL
Related parts for ADE7761AARS-RL
ADE7761AARS-RL Summary of contents
Page 1
FEATURES High accuracy, active energy measurement IC supports IEC 62053-21 Less than 0.1% error over a dynamic range of 500 to 1 Supplies active power on the frequency outputs, F1 and F2 High frequency output CF is intended for calibration ...
Page 2
ADE7761A TABLE OF CONTENTS Features .............................................................................................. 1 General Description ......................................................................... 1 Functional Block Diagram .............................................................. 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 Timing Characteristics ................................................................ 4 Absolute Maximum Ratings............................................................ 5 Performance Issues That May Affect Billing Accuracy........... 5 ESD Caution.................................................................................. ...
Page 3
SPECIFICATIONS ± 5%, AGND = DGND = 0 V, on-chip reference, on-chip oscillator Table 1. Parameter 1 ACCURACY 2 Measurement Error Phase Error Between Channels PF = 0.8 Capacitive PF = 0.5 Inductive 2 ...
Page 4
ADE7761A Parameter 5 LOGIC INPUTS PGA, SCF, S1, and S0 Input High Voltage, V INH Input Low Voltage, V INL Input Current Input Capacitance LOGIC OUTPUTS CF, REVP, and FAULT Output High Voltage ...
Page 5
ABSOLUTE MAXIMUM RATINGS T = 25°C, unless otherwise noted. A Table 3. Parameter V to AGND DD Analog Input Voltage to AGND MISCAL Reference Input ...
Page 6
ADE7761A PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Table 4. Pin Function Descriptions Pin No. Mnemonic Description 1 V Power Supply. This pin provides the supply voltage for the digital circuitry in the ADE7761A. The supply voltage DD should be maintained at ...
Page 7
Pin No. Mnemonic Description 15 FAULT This logic output goes active high when a fault or missing neutral condition occurs. A fault is defined as a condition under which the signals on V defined when the chip is powered up ...
Page 8
ADE7761A TERMINOLOGY Measurement Error The error associated with the energy measurement made by the ADE7761A is defined by = Percentage Error ⎛ − Energy registered by ADE7761A ⎜ ⎜ True Energy ⎝ Phase Error Between Channels The high-pass filter (HPF) ...
Page 9
TYPICAL PERFORMANCE CHARACTERISTICS 1 ON-CHIP REFERENCE 0.8 0.6 0.4 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 0.1 1.0 10.0 CURRENT (% of Full Scale) Figure 4. Active Power Error as a Percentage of Reading with Gain = ...
Page 10
ADE7761A TEST CIRCUIT 40A TO 80mA 18Ω 1MΩ 220V 1kΩ 33nF 10µF 100nF 1kΩ 33nF ADE7761A 1kΩ FAULT RB 33nF RCLKIN 1kΩ V ...
Page 11
OPERATION POWER SUPPLY MONITOR The ADE7761A continuously monitors the power supply (V with its on-chip, power supply monitor. If the supply is less than 4 V ± 5%, the ADE7761A goes into an inactive state, that is, no energy is ...
Page 12
ADE7761A The differential voltage MISCAL − common mode (usually AGND). The analog inputs of the ADE7761A can be driven with common-mode voltages 100 mV with respect to AGND. However, best results are achieved ...
Page 13
ANALOG-TO-DIGITAL CONVERSION The analog-to-digital conversion in the ADE7761A is carried out using second-order, Σ-Δ ADCs. Figure 19 shows a first- order, Σ-Δ ADC (for simplicity). The converter is made up of two parts: the Σ-Δ modulator and the digital low-pass ...
Page 14
ADE7761A ACTIVE POWER CALCULATION The ADCs digitize the voltage signals from the current and voltage transducers. A high-pass filter in the current channel removes any dc component from the current signal. This eliminates any inaccuracies in the active power calculation ...
Page 15
sin ≠ where: i(t) is the instantaneous current the dc component the rms ...
Page 16
ADE7761A DIGITAL-TO-FREQUENCY CONVERSION As previously described, the digital output of the low-pass filter after multiplication contains the active power information. However, because this LPF is not an ideal brick wall filter implementation, the output signal also contains attenuated components at ...
Page 17
Table 6. F Frequency Selection 1– (Hz) 1– 13.7 1 Values are generated using the nominal frequency of 450 kHz are a binary ...
Page 18
ADE7761A Fault with Active Input Greater than Inactive Input the active current input (that is, being used for billing), 1A and the voltage signal on V (inactive input) falls below 93.75 the fault ...
Page 19
244V rms POWER GENERATOR RB CT LOAD RF. Figure 31. Missing Neutral System Diagram The ADE7761A detects a missing neutral condition by continuously monitoring the voltage ...
Page 20
ADE7761A Missing Neutral Gain Calibration When the ADE7761A is in missing neutral mode, the energy is bill based on the active current input signal level. The frequency outputs in this mode can be calibrated with the MISCAL analog input pin. ...
Page 21
APPLICATIONS INTERFACING TO A MICROCONTROLLER FOR ENERGY MEASUREMENT The easiest way to interface the ADE7761A to a microcontroller is to use the CF high frequency output with the output frequency scaling set to 2048 × F1, F2. This is done ...
Page 22
ADE7761A Looking at Table 10, the closest frequency to 0.266 Hz in Column 4 is 0.17 Hz. Therefore, F2 (3.4 Hz; see Table 6) is selected for this design. Frequency Outputs Figure timing diagram for the various ...
Page 23
... OUTLINE DIMENSIONS 2.00 MAX 0.05 MIN COPLANARITY 0.10 ORDERING GUIDE Model Temperature Range ADE7761AARS –40°C to +85°C ADE7761AARS-RL –40°C to +85°C 1 ADE7761AARSZ –40°C to +85°C 1 ADE7761AARSZ-RL –40°C to +85°C ADE7761AARS-REF Pb-free part. 7.50 7.20 6. 5.60 5.30 8.20 5 ...
Page 24
ADE7761A NOTES ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05040-0-7/06(0) Rev Page ...