ALD1701SAL Advanced Linear Devices Inc, ALD1701SAL Datasheet - Page 4
![IC OPAMP GP R-R CMOS 8SOIC](/photos/18/28/182897/8-soic_sml.jpg)
ALD1701SAL
Manufacturer Part Number
ALD1701SAL
Description
IC OPAMP GP R-R CMOS 8SOIC
Manufacturer
Advanced Linear Devices Inc
Datasheet
1.ALD1701APAL.pdf
(9 pages)
Specifications of ALD1701SAL
Amplifier Type
General Purpose
Number Of Circuits
1
Output Type
Rail-to-Rail
Slew Rate
1 V/µs
Gain Bandwidth Product
1MHz
Current - Input Bias
1pA
Voltage - Input Offset
4500µV
Current - Supply
120µA
Current - Output / Channel
1mA
Voltage - Supply, Single/dual (±)
2 V ~ 12 V, ±1 V ~ 6 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (0.154", 3.90mm Width)
Number Of Channels
1
Voltage Gain Db
107.96 dB
Common Mode Rejection Ratio (min)
65 dB
Input Offset Voltage
4.5 mV
Operating Supply Voltage
3 V, 5, V, 9 V
Supply Current
0.25 mA
Maximum Power Dissipation
1.25 mW
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Maximum Dual Supply Voltage
+/- 6 V
Minimum Operating Temperature
0 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
-3db Bandwidth
-
Lead Free Status / Rohs Status
Details
Other names
1014-1076
ALD1701A/ALD1701B
ALD1701/ALD1701G
Design & Operating Notes:
1. The ALD1701A/ALD1701B/ALD1701/ALD1701G CMOS operational
2. The ALD1701A/ALD1701B/ALD1701/ALD1701G has complemen-
3. The input bias and offset currents are essentially input protection
amplifier uses a 3 gain stage architecture and an improved frequency
compensation scheme to achieve large voltage gain, high output
driving capability, and better frequency stability. In a conventional
CMOS operational amplifier design, compensation is achieved with
a pole splitting capacitor together with a nulling resistor. This method
is, however, very bias dependent and thus cannot accommodate the
large range of supply voltage operation as is required from a stand
alone CMOS operational amplifier.
ALD1701/ALD1701G is internally compensated for unity gain stability
using a novel scheme that does not use a nulling resistor. This
scheme produces a clean single pole roll off in the gain characteris-
tics while providing for more than 70 degrees of phase margin at the
unity gain frequency.
tary p-channel and n-channel input differential stages connected in
parallel to accomplish rail to rail input common mode voltage range.
This means that with the ranges of common mode input voltage close
to the power supplies, one of the two differential stages is switched
off internally. To maintain compatibility with other operational ampli-
fiers, this switching point has been selected to be about 1.5V below
the positive supply voltage. Since offset voltage trimming on the
ALD1701A/ALD1701B/ALD1701/ALD1701G is made when the input
voltage is symmetrical to the supply voltages, this internal switching
does not affect a large variety of applications such as an inverting
amplifier or non-inverting amplifier with a gain larger than 2.5 (5V
operation), where the common mode voltage does not make excur-
sions above this switching point. The user should however, be aware
that this switching does take place if the operational amplifier is
connected as a unity gain buffer, and should make provision in his
design to allow for input offset voltage variations.
diode reverse bias leakage currents, and are typically less than 1pA
1000
400
300
200
100
100
10
0
1
10K
0
SUPPLY CURRENT AS A FUNCTION
INPUTS GROUNDED
OUTPUT UNLOADED
OPEN LOOP VOLTAGE GAIN AS A
FUNCTION OF LOAD RESISTANCE
±1
OF SUPPLY VOLTAGE
T
A
SUPPLY VOLTAGE (V)
= -55°C
100K
±2
LOAD RESISTANCE (Ω)
TYPICAL PERFORMANCE CHARACTERISTICS
±3
-25°C
+70°C
+25°C
The ALD1701A/ALD1701B/
±4
1M
V
T
+125°C
A
S
±5
= ±2.5V
= 25°C
Advanced Linear Devices
10M
±6
4. The output stage consists of class AB complementary output drivers,
5. The ALD1701A/ALD1701B/ALD1701/ALD1701G operational ampli-
6. The ALD1701A/ALD1701B/ALD1701/ALD1701G, with its
at room temperature. This low input bias current assures that the
analog signal from the source will not be distorted by input bias
currents. Normally, this extremely high input impedance of greater
than 10
limit the node impedance. However, for applications where source
impedance is very high, it may be necessary to limit noise and hum
pickup through proper shielding.
capable of driving a low resistance load. The output voltage swing is
limited by the drain to source on-resistance of the output transistors
as determined by the bias circuitry, and the value of the load resistor.
When connected in the voltage follower configuration, the oscillation
resistant feature, combined with the rail to rail input and output
feature, makes an effective analog signal buffer for medium to high
source impedance sensors, transducers, and other circuit networks.
fier has been designed to provide full static discharge protection.
Internally, the design has been carefully implemented to minimize
latch up. However, care must be exercised when handling the device
to avoid strong static fields that may degrade a diode junction, causing
increased input leakage currents. In using the operational amplifier,
the user is advised to power up the circuit before, or simultaneously
with any input voltages applied, and to limit input voltages not to
exceed 0.3V of the power supply voltage levels.
micropower operation, offers numerous benefits in reduced power
supply requirements, less noise coupling and current spikes, less
thermally induced drift, better overall reliability due to lower self
heating, and lower input bias current. It requires practically no warm
up time as the chip junction heats up to only 0.1°C above ambient
temperature under most operating conditions.
10000
1000
100
12
1.0
±7
±6
±5
±4
±3
±2
±1
0.1
10
Ω would not be a problem as the source impedance would
0
COMMON MODE INPUT VOLTAGE RANGE
-50
0
AS A FUNCTION OF SUPPLY VOLTAGE
INPUT BIAS CURRENT AS A FUNCTION
±1
-25
T
V
OF AMBIENT TEMPERATURE
A
S
= 25°C
= ±2.5V
AMBIENT TEMPERATURE (°C)
±2
SUPPLY VOLTAGE (V)
0
±3
25
±4
50
±5
75
±6
100
±7
125
4 of 9