XC56309VF100A Freescale Semiconductor, XC56309VF100A Datasheet - Page 86

• Manufacturer Part Number: XC56309VF100A
• Description: IC DSP 24BIT FIXED-POINT 196-BGA
• Manufacturer: Freescale Semiconductor
• Series: DSP563xxr
• Type: Fixed Pointr

Specifications of XC56309VF100A

• Interface: Host Interface, SSI, SCI
• Clock Rate: 100MHz
• Non-volatile Memory: ROM (576 B)
• On-chip Ram: 24kB
• Voltage - I/o: 3.30V
• Voltage - Core: 3.30V
• Operating Temperature: -40°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 196-MAPBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Core Configuration
4.7 DMA Control Registers 5–0 (DCR[5–0])
The DMA Control Registers (DCR[5–0]) are read/write registers that control the DMA operation
for each of their respective channels. All DCR bits are cleared during processor reset.
4-28
Number
Number
1–0
Bit
Bit
DRS0
23
22
DE
23
11
Bit Name
Bit Name
D3D
BAT
DIE
DIE
22
10
DE
Table 4-10. Address Attribute Registers (AAR[0–3]) Bit Definitions
DTM2
DAM5
Table 4-11. DMA Control Register (DCR) Bit Definitions
Reset
Reset
Value
Value
21
9
0
0
0
DTM1
DAM4
DMA Channel Enable
Enables the channel operation. Setting DE either triggers a single block DMA transfer in the
DMA transfer mode that uses DE as a trigger or enables a single-block, single-line, or
single-word DMA transfer in the transfer modes that use a requesting device as a trigger.
DE is cleared by the end of DMA transfer in some of the transfer modes defined by the DTM
bits. If software explicitly clears DE during a DMA operation, the channel operation stops
only after the current DMA transfer completes (that is, the current word is stored into the
destination).
DMA Interrupt Enable
Generates a DMA interrupt at the end of a DMA block transfer after the counter is loaded
with its preloaded value. A DMA interrupt is also generated when software explicitly clears
DE during a DMA operation. Once asserted, a DMA interrupt request can be cleared only
by the service of a DMA interrupt routine. To ensure that a new interrupt request is not
generated, clear DIE while the DMA interrupt is serviced and before a new DMA request is
generated at the end of a DMA block transfer—that is, at the beginning of the DMA channel
interrupt service routine. When DIE is cleared, the DMA interrupt is disabled.
Bus Access Type
Read/write bits that define the type of external memory (DRAM or SRAM) to access for the
area defined by the BAC[11–0],BYEN, BXEN, and BPEN bits. The encoding of BAT[1–0] is:
When the external access type is defined as a DRAM access (BAT[1–0] = 10), AA/RAS acts
as a Row Address Strobe (RAS) signal. Otherwise, it acts as an Address Attribute signal.
External accesses to the default area always execute as if BAT[1–0] = 01 (that is, SRAM
access). If Port A is used for external accesses, the BAT bits in the AAR3–0 registers must
be initialized to the SRAM access type (that is, BAT = 01) or to the DRAM access type (that
is BAT = 10). To ensure proper operation of Port A, this initialization must occur even for an
AAR register that is not used during any Port A access. Note that at reset, the BAT bits are
initialized to 00.
Figure 4-9. DMA Control Register (DCR)
20
8
00 = Reserved
01 = SRAM access
10 = DRAM access
11 = Reserved
DTM0
DAM3
DSP56309 User’s Manual, Rev. 1
19
7
DAM2
DPR1
18
6
DPR0
DAM1
17
5
Description
Description
DCON
DAM0
16
4
DRS4
DDS1
15
3
DRS3
DDS0
14
2
Freescale Semiconductor
DRS2
DSS1
13
1
DRS1
DSS0
12
0