75005-0204 Molex Inc, 75005-0204 Datasheet - Page 5
![CONN RECEPT 72POS 1.2MM VERT SMD](/photos/1/80/18088/75005-0204_sml.jpg)
75005-0204
Manufacturer Part Number
75005-0204
Description
CONN RECEPT 72POS 1.2MM VERT SMD
Manufacturer
Molex Inc
Series
Plateau HS Mezz™ 75005r
Datasheets
1.75005-0306.pdf
(7 pages)
2.75005-0306.pdf
(9 pages)
3.75005-0306.pdf
(12 pages)
4.75005-0204.pdf
(3 pages)
Specifications of 75005-0204
Connector Type
Differential Pair Array, Female
Number Of Positions
72
Pitch
0.047" (1.20mm)
Number Of Rows
2
Mounting Type
Surface Mount
Features
Board Guide
Contact Finish
Gold
Contact Finish Thickness
30µin (0.76µm)
Mated Stacking Heights
10mm, 13mm, 15mm
Height Above Board
0.285" (7.24mm)
Pitch Spacing
1.2mm
No. Of Contacts
72
Gender
Receptacle
Contact Plating
Gold
No. Of Rows
2
Contact Termination
Surface Mount Vertical
Product Type
Receptacles
Mounting Style
Wire
Mounting Angle
Vertical
Number Of Positions / Contacts
16
Housing Material
High Temperature Thermoplastic
Contact Material
High Performance Alloy (HPA)
Voltage Rating
30 V
Current Rating
1.5 A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
075005-0204
0750050204
750050204
WM17207TR
0750050204
750050204
WM17207TR
REVISION:
DOCUMENT NUMBER:
B
PS-75005-001
5.4.2 Temperature Life: There shall be no change in contact resistance greater than 10mOhms
5.4.3 Temperature Life (preconditioning): There shall be no change in contact resistance greater
5.4.4 Cyclic Humidity: There shall be no change in contact resistance greater than 10mOhms
5.4.5 Thermal Disturbance: There shall be no change in contact resistance greater than 10mOhms
5.4.6 Mixed Flowing Gas: There shall be no change in contact resistance greater than 10mOhms
5.4.7 Thermal Cycling: There shall be no change in contact resistance greater than 10mOhms
5.4.8 Temperature Rise: Apply an increasing current and monitor temperature until a DT of
5.4.9 Plating Adhesion: Plating will show no flaking, peeling, or other adhesion failure after
ECR/ECN INFORMATION:
EC No:
DATE:
from initial when mated specimens are subjected to 85
17, Method A, Test Condition 4.
from initial when mated specimens are subjected to 24 cycles between 25
65
extremes. Test per EIA-364-31.
from initial when mated specimens are cycled between 15
Temperature ramp should be 2
from initial when mated and unmated specimens are subjected to environmental Class II for
7 days. Test per EIA-364-65, for unmated specimens use Option 2.
from initial when mated specimens are cycled between 15
of 2
cycle 500 times.
30
was achieved as follows: 96 hours steady state, 240 hours current cycling (45 minutes on,
15 minutes off, repeat), 96 Hours steady state. Upon completion of the test, if the
temperature is below the DT of 30
the rated current.
being exposed to the following environmental sequences and then being subjected to a cross
cut tape test. The test will be performed as follows: one exposure to IR or convection oven
reflow temperatures, 5 cycles between -55
and 20 cycles of 4-4-16 (4 hours at 75
+/- 2.5
Test adhesion per ASTM D 3359-78 Method B.
than 10mOhms from initial when mated specimens are subjected to 85
Test per EIA-364-17, Method A, Test Condition 4.
UCP2003-2204
2003 / 04 / 10
o
o
C at 50 RH, with a 0.5 hour ramp time between extremes and a 1.0 hour dwell time at
C over the ambient temperature is achieved. Test at the current at which a DT of 30
o
C per minute. With a dwell time of at least 5 minutes. Humidity is not controlled,
o
C and 47.5% RH +/- 2.5%, 16 hours at 25
PRODUCT SPECIFICATION
HIGH SPEED MEZZANINE
TITLE:
CREATED / REVISED BY:
Ken Stiles
BOARD TO BOARD CONNECTOR SYSTEM
PRODUCT SPECIFICATION FOR THE
o
C per minute minimum with 5 minute dwell minimum.
o
C, then the current at which the test was run becomes
HIGH SPEED MEZZANINE
o
C +/- 2.5
o
C and 85
o
C and 92.5% RH +/- 2.5%, 4 hours at 75
CHECKED BY:
o
Ken Stiles
C +/- 2.5
o
C with 30 minute dwell at extremes,
o
C for 1000 hours. Test per EIA-364-
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
o
o
C and 85
C and 85
o
C and 47.5% RH +/- 2.5%).
o
o
C for 10 cycles .
C at a minimum ramp
o
C for 250 hours.
Manny Banakis
APPROVED BY:
o
C at 80% RH and
SHEET No.
5
of
7
o
C
o
C