RT0603DRD072K49L Yageo, RT0603DRD072K49L Datasheet - Page 8
![RES 2.49K OHM 1/10W .5% 0603 SMD](/photos/12/74/127462/rc0603fr-0710rl_sml.jpg)
RT0603DRD072K49L
Manufacturer Part Number
RT0603DRD072K49L
Description
RES 2.49K OHM 1/10W .5% 0603 SMD
Manufacturer
Yageo
Series
RTr
Datasheet
1.RT0402FRE0727KL.pdf
(10 pages)
Specifications of RT0603DRD072K49L
Resistance (ohms)
2.49K
Power (watts)
0.1W, 1/10W
Composition
Thin Film
Temperature Coefficient
±25ppm/°C
Tolerance
±0.5%
Size / Dimension
0.063" L x 0.031" W (1.60mm x 0.80mm)
Height
0.018" (0.45mm)
Lead Style
Surface Mount (SMD - SMT)
Package / Case
0603 (1608 Metric)
Resistance In Ohms
2.49K
Case
0603 (1608 metric)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Other names
311-2.49KDTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
RT0603DRD072K49L
Manufacturer:
Yageo
Quantity:
4 000
TEST
Short Time Overload
Board Flex/
Bending
Low Temperature
Operation
Insulation Resistance
Dielectric Withstand
Voltage
Solderability
Oct 21, 2009 V.4
- Wetting
- Leaching
- Resistance to
Soldering Heat
Chip Resistor Surface Mount
TEST METHOD
IEC60115-1 4.13
IEC 60068-2-21
IEC 60068-2-1
IEC 60115-1 4.6
IEC 60115-1 4.7
IPC/JEDEC J-STD-002B test B
IPC/JEDEC J-STD-002B test D
IEC 60068-2-58
RT
Electrical Test not required
Magnification 50X
SMD conditions:
1
2
PROCEDURE
2.5 times of rated voltage or maximum
overload voltage whichever is less for 5 sec at
room temperature
Chips mounted on a 90mm glass epoxy resin
PCB (FR4)
Bending: see table 6 for each size
Bending time: 60±5 seconds
The resistor shall be subjected to a DC rated
voltage for 1.5 h-on, 0.5 h-off, at -55±3 °C
This constitutes shall be repeated for 96 hours
However the applied voltage shall not exceed
the maximum operating voltage
Rated continuous overload voltage (RCOV)
for 1 minute
Details see below table 5
Maximum voltage (V
Details see below table 5
Leadfree solder, 260 °C, 30 seconds
immersion time
Condition B, no pre-heat of samples.
Leadfree solder, 260 °C, 10 seconds
immersion time
Procedure 2 for SMD: devices fluxed and
cleaned with isopropanol
st
nd
step: method B, aging 4 hours at 155°C
step: leadfree solder bath at 245±3°C
SERIES
dry heat
Dipping time: 3±0.5 seconds
0402 to 2512 (RoHS Compliant)
rms
) applied for 1 minute
REQUIREMENTS
±(0.5%+0.05 Ω)
No visible damage
±(0.25%+0.05 Ω)
No visible damage
±(0.5%+0.05 Ω)
No visible damage
≥10 GΩ
No breakdown or flashover
Well tinned (≥95%
covered)
No visible damage
No visible damage
±(0.5%+0.05 Ω)
No visible damage
Product specification
www.yageo.com
10
8