TISP4240M3BJR Bourns Inc., TISP4240M3BJR Datasheet - Page 9
![SURGE SUPP 180V BIDIR DO-214AA](/photos/27/89/278985/do-214aa_smb_sml.jpg)
TISP4240M3BJR
Manufacturer Part Number
TISP4240M3BJR
Description
SURGE SUPP 180V BIDIR DO-214AA
Manufacturer
Bourns Inc.
Specifications of TISP4240M3BJR
Package / Case
DO-214AA, SMB
Voltage - Breakover
240V
Voltage - Off State
180V
Voltage - On State
3V
Current - Peak Pulse (8 X 20µs)
220A
Current - Peak Pulse (10 X 1000µs)
50A
Current - Hold (ih)
150mA
Number Of Elements
1
Capacitance
50pF
Breakover Current Ibo Max
32 A
Rated Repetitive Off-state Voltage Vdrm
180 V
Off-state Leakage Current @ Vdrm Idrm
0.005 mA
Forward Voltage Drop
3 V
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TISP4240M3BJR
Manufacturer:
BOURNS
Quantity:
45 000
Company:
Part Number:
TISP4240M3BJR-S
Manufacturer:
BOURNS
Quantity:
240 000
Part Number:
TISP4240M3BJR-S
Manufacturer:
BOURNS/伯恩斯
Quantity:
20 000
These devices are two terminal overvoltage protectors. They may be used either singly to limit the voltage between two conductors (Figure 13)
or in multiples to limit the voltage at several points in a circuit (Figure 14).
In Figure 13, protector Th1 limits the maximum voltage between the two conductors to ±V (BO) . This configuration is normally used to protect
circuits without a ground reference, such as modems. In Figure 14, protectors Th2 and Th3 limit the maximum voltage between each conduc-
tor and ground to the ±V (BO) of the individual protector. Protector Th1 limits the maximum voltage between the two conductors to its ±V (BO)
value. If the equipment being protected has all its vulnerable components connected between the conductors and ground, then protector Th1
is not required.
To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms.
The table below shows some common values.
If the impulse generator current exceeds the protector’s current rating, then a series resistance can be used to reduce the current to the
protector’s rated value to prevent possible failure. The required value of series resistance for a given waveform is given by the following
calculations. First, the minimum total circuit impedance is found by dividing the impulse generator’s peak voltage by the protector’s rated
current. The impulse generator’s fictive impedance (generator’s peak voltage divided by peak short circuit current) is then subtracted from the
minimum total circuit impedance to give the required value of series resistance.
For the FCC Part 68 10/560 waveform, the following values result. The minimum total circuit impedance is 800/75 = 10.7 Ω and the generator’s
fictive impedance is 800/100 = 8 Ω. This gives a minimum series resistance value of 10.7 - 8 = 2.7 Ω. After allowing for tolerance, a 3 Ω ±10%
resistor would be suitable. The 10/160 waveform needs a standard resistor value of 5.6 Ω per conductor. These would be R1a and R1b in
Figure 16 and Figure 17. FCC Part 68 allows the equipment to be non-operational after the 10/160 (conductor to ground) and 10/560 (inter-
conductor) impulses. The series resistor value may be reduced to zero to pass FCC Part 68 in a non-operational mode, e.g. Figure 15. For this
type of design, the series fuse must open before the TISP4xxxM3 fails. For Figure 15, the maximum fuse i
equipment will require verification over a temperature range. By using the rated waveform values from Figure 12, the appropriate series resistor
value can be calculated for ambient temperatures in the range of -40 °C to 85 °C.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
NOVEMBER 1997 - REVISED MAY 2007
Deployment
Impulse Testing
† FCC Part 68 terminology for the waveforms produced by the ITU-T recommendation K.21 10/700 impulse generator
GR-1089-CORE
ITU-T K.20/K.21
(March 1998)
FCC Part 68
Standard
I3124
TISP4xxxM3BJ Overvoltage Protector Series
Figure 13. Two Point Protection
Peak Voltage
Setting
2500
1000
1500
1500
1000
1500
1500
4000
800
V
Th1
Wave Shape
10/1000
Voltage
9/720 †
9/720 †
0.5/700
10/160
10/560
10/700
2/10
APPLICATIONS INFORMATION
Peak Current
Value
37.5
37.5
37.5
500
100
200
100
100
25
A
Wave Shape
10/1000
Current
5/320 †
5/320 †
0.2/310
10/160
10/560
5/310
2/10
Figure 14. Multi-Point Protection
TISP4XXXM3
25 °C Rating
Th1
300
120
100
100
100
100
75
50
A
2
t is 2.3 A
Th3
Th2
Resistance
Series
2x5.6
11
2
3
0
0
0
0
s. In some cases, the