CS52015-1GT3 ON Semiconductor, CS52015-1GT3 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
CS52015-1GT3
Manufacturer Part Number
CS52015-1GT3
Description
IC REG LIN 1.5A ADJ-OUT TO220AB
Manufacturer
ON Semiconductor
Datasheet
1.CS52015-1GSTR3.pdf
(9 pages)
Specifications of CS52015-1GT3
Regulator Topology
Positive Adjustable
Voltage - Output
1.25 ~ 5.5 V
Voltage - Input
Up to 7V
Voltage - Dropout (typical)
1.05V @ 1.5A
Number Of Regulators
1
Current - Output
1.5A
Current - Limit (min)
1.6A
Operating Temperature
0°C ~ 70°C
Mounting Type
Through Hole
Package / Case
TO-220-3 (Straight Leads)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
CS52015-1GT3OS
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS52015-1GT3
Manufacturer:
ON
Quantity:
50 210
2.0 mA. R1 and R2 should be the same type, e.g. metal film
for best tracking over temperature. While not required, a
bypass capacitor from the adjust pin to ground will improve
ripple rejection and transient response. A 0.1 mF tantalum
capacitor is recommended for “first cut” design. Type and
value may be varied to obtain optimum performance vs.
price.
Short Circuit Protection
maximum specification of 7.0 V for the voltage difference
between V
regulate voltages in excess of 7.0 V. The main considerations
in such a design are power−up and short circuit capability.
is fairly slow, typically on the order of several tens of
milliseconds, while the regulator responds in less than one
microsecond. In this case, the linear regulator begins
charging the load as soon as the V
large enough that the pass transistor conducts current. The
load at this point is essentially at ground, and the supply
voltage is on the order of several hundred millivolts, with the
result that the pass transistor is in dropout. As the supply to
V
current is passed to the load until V
which the IC is in regulation. Further increase in the supply
voltage brings the pass transistor out of dropout. The result
is that the output voltage follows the power supply ramp−up,
staying in dropout until the regulation point is reached. In
this manner, any output voltage may be regulated. There is
no theoretical limit to the regulated voltage as long as the
V
circuit condition is very real for this type of design. Short
circuit conditions will result in the immediate operation of
the pass transistor outside of its safe operating area.
Over−voltage stresses will then cause destruction of the pass
transistor before overcurrent or thermal shutdown circuitry
can become active. Additional circuitry may be required to
clamp the V
fail−safe operation is required. One possible clamp circuit is
IN
IN
R1 is chosen so that the minimum load current is at least
The CS52015−1 linear regulator has an absolute
In most applications, ramp−up of the power supply to V
However, the possibility of destroying the IC in a short
V
increases, the pass transistor will remain in dropout, and
to V
IN
OUT
Figure 11. Resistor Divider Scheme
IN
C
IN
differential of 7.0 V is not exceeded.
and V
1
to V
V
CS52015−1
IN
OUT
OUT
Adj
. However, the IC may be used to
differential to less than 7.0 V if
V
C
OUT
Adj
I
Adj
V
IN
REF
OUT
to V
reaches the point at
R
R
OUT
1
2
differential is
C
V
2
OUT
http://onsemi.com
IN
5
illustrated in Figure 12; however, the design of clamp
circuitry must be done on an application by application
basis. Care must be taken to ensure the clamp actually
protects the design. Components used in the clamp design
must be able to withstand the short circuit condition
indefinitely while protecting the IC.
Stability Considerations
main characteristics of a linear regulator: start−up delay,
load transient response, and loop stability.
size and temperature constraints. A tantalum or aluminum
electrolytic capacitor is best, since a film or ceramic
capacitor with almost zero ESR can cause instability. The
aluminum electrolytic capacitor is the least expensive
solution. However, when the circuit operates at low
temperatures, both the value and ESR of the capacitor will
vary considerably. The capacitor manufacturer’s data sheet
provides this information.
applications, but with high current regulators such as the
CS52015−1 the transient response and stability improve
with higher values of capacitance. The majority of
applications for this regulator involve large changes in load
current so the output capacitor must supply the
instantaneous load current. The ESR of the output capacitor
causes an immediate drop in output voltage given by:
output capacitor network consisting of several tantalum and
ceramic capacitors in parallel. This reduces the overall ESR
and reduces the instantaneous output voltage drop under
transient load conditions. The output capacitor network
should be as close as possible to the load for the best results.
The output compensation capacitor helps determine three
The capacitor value and type is based on cost, availability,
A 22 mF tantalum capacitor will work for most
For microprocessor applications it is customary to use an
EXTERNAL SUPPLY
Figure 12. Short Circuit Protection Circuit for
V
IN
High Voltage Application.
V
Adj
DV + DI
V
OUT
V
ESR
OUT