MIC5213-1.8BC5 TR Micrel Inc, MIC5213-1.8BC5 TR Datasheet - Page 7
![IC REG LDO 80MA 1.8V SC70-5](/photos/28/20/282067/sc-70-5__sot-323-5_sml.jpg)
MIC5213-1.8BC5 TR
Manufacturer Part Number
MIC5213-1.8BC5 TR
Description
IC REG LDO 80MA 1.8V SC70-5
Manufacturer
Micrel Inc
Series
Teeny™r
Datasheet
1.MIC5213-3.3YC5_TR.pdf
(8 pages)
Specifications of MIC5213-1.8BC5 TR
Regulator Topology
Positive Fixed
Voltage - Output
1.8V
Voltage - Input
2.5 ~ 16 V
Voltage - Dropout (typical)
0.28V @ 80mA
Number Of Regulators
1
Current - Output
80mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
SC-70-5, SC-88A, SOT-323-5, SOT-353, 5-TSSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Limit (min)
-
Other names
MIC5213-1.8BC5TR
MIC5213-1.8BC5TR
MIC5213-1.8BC5TR
August 2004
MIC5213
Applications Information
Input Capacitor
A 0.1 F capacitor should be placed from IN to GND if there
is more than 10 inches of wire between the input and the ac
filter capacitor or when a battery is used as the input.
Output Capacitor
Typical PNP-based regulators require an output capacitor to
prevent oscillation. The MIC5213 is ultrastable, requiring only
0.47 F of output capacitance for stability. The regulator is
stable with all types of capacitors, including the tiny, low-ESR
ceramic chip capacitors. The output capacitor value can be
increased without limit to improve transient response.
No-Load Stability
The MIC5213 will remain stable and in regulation with no load
(other than the internal voltage divider) unlike many other
voltage regulators. This is especially important in CMOS
RAM keep-alive applications.
Enable Input
The MIC5213 features nearly zero off-mode current. When
EN (enable input) is held below 0.6V, all internal circuitry is
powered off. Pulling EN high (over 2.0V) re-enables the
device and allows operation. When EN is held low, the
regulator typically draws only 10nA of current. While the logic
threshold is TTL/CMOS compatible, EN may be pulled as
high as 20V, independent of V
Thermal Behavior
The MIC5213 is designed to provide 80mA of continuous
current in a very small profile package. Maximum power
dissipation can be calculated based on the output current and
the voltage drop across the part. To determine the maximum
power dissipation of the package, use the junction-to-ambi-
ent thermal resistance of the device and the following basic
equation:
T
125 C, and T
the junction-to-ambient thermal resistance ambient of the
regulator. The
J(max)
P
D(max)
is the maximum junction temperature of the die,
A
is the maximum ambient temperature.
T
JA
J(max)
of the MIC5213 is 450 C/W.
JA
T
A
IN
.
JA
is
7
The actual power dissipation of the regulator circuit can be
determined using one simple equation.
Substituting P
for the operating conditions that are critical to the application
will give the maximum operating conditions for the regulator
circuit. For example, if we are operating the MIC5213-3.0BC5
at room temperature, with a minimum footprint layout, we can
determine the maximum input voltage for a set output current.
To prevent the device from entering thermal shutdown,
maximum power dissipation cannot be exceeded. Using the
output voltage of 3.0V, and an output current of 80mA, we can
determine the maximum input voltage. Ground current, maxi-
mum of 3mA for 80mA of output current, can be taken from
the “Electrical Characteristics” section of the data sheet.
Therefore, a 3.0V application at 80mA of output current can
accept a maximum input voltage of 5.6V in an SC-70-5
package. For a full discussion of heat sinking and thermal
effects on voltage regulators, refer to Regulator Thermals
section of Micrel’s
lators
Fixed Voltage Regulator
The MIC5213 is ideal for general-purpose voltage regulation
in any handheld device. Applications that are tight for space
can easily use the Teeny™ SC-70 regulator which occupies
half the space of a SOT-23-5 regulator. The MIC5203 offers
a smaller system solution, only requiring a small multilayer
ceramic capacitor for stability.
P
222mW = (V
222mW = (80mA
462mW = 83mA
V
P
P
handbook.
D(max)
D(max)
D
IN
= (V
= 5.57V max.
Li-Ion
3.6V
Cell
Figure 1. Single-Cell Regulator
IN
D(max)
222mW
– V
450 C / W
125 25
Designing with Low-Dropout Voltage Regu-
IN
OUT
, determined above, for P
– 3.0V) 80mA + V
) I
V
OUT
MIC5213-x.x
IN
EN
V
IN
IN
GND
+ 3mA
+ V
OUT
IN
I
GND
V
IN
IN
0.47µF
) – 240mW
V
3.0V
3mA
OUT
D
and solving
MIC5213
Micrel