LX8386-00CDD Microsemi Analog Mixed Signal Group, LX8386-00CDD Datasheet
LX8386-00CDD
Specifications of LX8386-00CDD
Available stocks
Related parts for LX8386-00CDD
LX8386-00CDD Summary of contents
Page 1
... Note: Available in Tape & Reel. Append the letters “TR” to the part number. (i.e. LX8386-xxCP-TR) Copyright © 2000 Rev. 2.0, 2005-11-02 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 ® 1.5A Low Dropout Positive Regulators ...
Page 2
... A 60°C/W MBIENT JA , θ 2.7°C θ A 60°C/W MBIENT JA , θ 2.7°C θ Thermal Bandgap Control Circuit Circuit Microsemi Linfinity Microelectronics Division LX8386x- RODUCTION ATA HEET TAB is V OUT OUT ADJ / 1 GND (3- ) ACKAGE PIN (Top View) TAB is V OUT OUT (3- ...
Page 3
... TM Unless otherwise specified, the following specifications apply over the operating ambient temperature for the LX8386x-xxC with ≤ ≤ 0°C T 125°C and the LX8386-xxI with -25° 1.5A. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient OUT temperature ...
Page 4
... Unless otherwise specified, the following specifications apply over the operating ambient temperature for the LX8386x-xxC with ≤ ≤ 0°C T 125°C and the LX8386-xxI with -25° 3A. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient OUT temperature ...
Page 5
... TM The LX8386/86A/86B Series ICs are easy to use Low- Dropout (LDO) voltage regulators. They have all of the standard self-protection features expected of a voltage regulator: short circuit protection, safe operating area protection and automatic thermal shutdown if the device temperature rises above approximately 165°C. ...
Page 6
... OUTPUT VOLTAGE The LX8386/86A/86B ICs develop a 1.25V reference voltage between the output and the adjust terminal (See Figure 2). By placing a resistor, R1, between these two terminals, a constant current is caused to flow through R1 and down through R2 to set the overall output voltage ...
Page 7
... DROPOUT(MAX) installed regulator. THERMAL CONSIDERATIONS The LX8386/86A/86B regulators have internal power and thermal limiting circuitry designed to protect each device under overload conditions. For continuous normal load conditions, however, maximum junction temperature ratings must not be exceeded ...
Page 8
... HEET IN OUT Part LX8386 R1 121Ω 1% ADJ + R2 1k ⎛ ⎞ R2 ⎜ ⎟ + 1.25V 1 ⎝ ⎠ OUT Part 3.3V LX8386 Min. 15µF Tantalum or 100µF Aluminum capacitor. ADJ May be increased without limit. ESR must be less than <400mΩ OUT C2 100µF Page 8 ...
Page 9
... Dim Seating Plane Microsemi Linfinity Microelectronics Division LX8386x- RODUCTION ATA HEET M I ILLIMETERS NCHES MIN MAX MIN MAX 14.22 15.88 0.560 0.625 9.65 10.67 0.380 0.420 3.56 4.83 0.140 0.190 0.51 1.14 0.020 0.045 3.53 4.09 0.139 0.161 2.54 BSC 0.100 BSC 6 ...
Page 10
... Low Dropout Positive Regulators Dim 0. Microsemi Linfinity Microelectronics Division LX8386x- RODUCTION ATA HEET M I ILLIMETERS NCHES MIN MAX MIN MAX 6.47 6.73 0.255 0.265 5.97 6.23 0.235 0.245 2.16 2.42 0.085 0.095 0.68 0.94 0.027 0.037 0.38 0.64 0.015 0.025 0.63 0.89 0.025 0.035 2 ...
Page 11
... Microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time. Copyright © 2000 Rev. 2.0, 2005-11-02 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 ® 1.5A Low Dropout Positive Regulators P RODUCTION Microsemi Linfinity Microelectronics Division LX8386x- ATA HEET Page 11 ...