MIC2214-SGBML TR Micrel Inc, MIC2214-SGBML TR Datasheet - Page 3
![IC REG LDO DUAL OPEN DRAIN 10MLF](/photos/7/34/73421/576-10-mlf_sml.jpg)
MIC2214-SGBML TR
Manufacturer Part Number
MIC2214-SGBML TR
Description
IC REG LDO DUAL OPEN DRAIN 10MLF
Manufacturer
Micrel Inc
Datasheet
1.MIC2214-SGYML_TR.pdf
(11 pages)
Specifications of MIC2214-SGBML TR
Regulator Topology
Positive Fixed
Voltage - Output
3.3V, 1.8V
Voltage - Input
2.25 ~ 5.5 V
Voltage - Dropout (typical)
0.12V @ 150mA, 0.24V @ 300mA
Number Of Regulators
2
Current - Output
150mA, 300mA
Current - Limit (min)
150mA, 300mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
10-MLF®, QFN
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
MIC2214-SGBMLTR
MIC2214-SGBMLTR
MIC2214-SGBMLTR
Pin Configuration
Pin Description
October 2005
Pin Number
MLF-10 (3x3)
EP
10
1
2
–
–
3
4
–
5
6
–
–
7
8
9
10-Pin 3mm × 3mm MLF™ (ML)
BYP
SET
VIN
SW
Pin Number
MLF-16 (4x4)
EN
15, 16
1
2
3
4
5
7,8
EP
10
12
13
14
11
–
1
2
3
5
4
6
9
(Top View)
Pin Name
10 VOUT1
VOUT2
VOUT1
9
8
7
6
NGND
CBYP
ADJ1
ADJ2
GND
POR
GND
DRV
EN1
EN2
SET
VIN
SW
EN
VOUT2
POR
DRV
GND
Pin Function
Supply Input: (VIN1 and VIN2 are internally tied together)
Enable Input: Enables both regulator outputs. Active High. High = on, low =
off. Do not leave floating.
Enable Input to Regulator 1: Enables regulator 1 output. Active high input.
High = on, low = off. Do not leave floating.
Enable Input to Regulator 2: Enables regulator 2 output. Active high input.
High = on, low = off. Do not leave floating.
Reference Bypass: Connect external 0.01µF to GND to reduce output noise.
May be left open.
Active high signal drives open-drain N-Channel MOSFET.
Adjust Input (Regulator 1): Connect feedback resistors to program the out-
put voltage for the regulator.
Delay Set Input: Connect external capacitor to GND to set the internal delay
for the POR output. When left open, there is no delay. This pin cannot be
grounded.
Ground: Connect externally to exposed pad.
Ground for the open-drain driver. Tied to the source of the NMOSFET. Tied
to GND internally.
Adjust Input (Regulator 2): Connect feedback resistors to program the out-
put voltage for the regulator.
Open-Drain Output: Capable of sinking 150mA.
Power-On Reset Output: Open-drain output. Active low indicates an output
undervoltage condition on regulator 2.
Output of Regulator 2: 300mA output current
Output of Regulator 1: 150mA output current
Ground: Internally connected to the exposed pad. Connect externally to
ground pin.
3
ADJ1
16-Pin 4mm × 4mm MLF™ (ML)
BYP
EN1
EN2
1
2
3
4
16
5
15
6
14
7
13
8
12
11
10
9
POR
DRV
ADJ
NGND
M9999-101705