BA00JC5WT Rohm Semiconductor, BA00JC5WT Datasheet
![no-image](/images/manufacturer_photos/0/5/572/rohm_semiconductor_sml.jpg)
BA00JC5WT
Specifications of BA00JC5WT
Available stocks
Related parts for BA00JC5WT
BA00JC5WT Summary of contents
Page 1
... BA□□JC5 Series Secondary Variable Output LDO Regulator BA00JC5WT Description The BA□□JC5 are low-saturation regulators with an output current of 1.5 A and a voltage accuracy of 1%. A broad output voltage range is offered, from 1.5V to 12V, and built-in overcurrent protection and thermal shutdown (TSD) circuits prevent damage due to short-circuiting and overloading, respectively. ...
Page 2
... BA□□JC5 Series,BA00JC5WT Product Lineup Part Number 1.5 1.8 2.5 BA□□JC5T BA□□JC5WT - - Part Number: BA□□JC5□ □ Symbol Output voltage (V) □□ Existence of switch With W: A shutdown switch is provided Package T: Absolute Maximum Ratings (Ta = 25℃) Parameter ...
Page 3
... Vcc : 6 Vcc = 9 8 Vcc = 9 Vcc = Vcc = ≥ 3 Change Vcc from 3 1.5 V ≤ Vo ≤ 2 Operation guaranteed BA00JC5WT (−V5)(Unless otherwise specified 25℃, Vcc = 3 Parameter Reference voltage Shutdown circuit current Minimum I/O voltage difference Output current capacity Input stability Load stability Temperature coefficient of output voltage VOUT = Vc ...
Page 4
... BA□□JC5 Series,BA00JC5WT Electrical Characteristics Curves (Unless otherwise specified 25℃; Vcc = 0.6 0.5 [BA50JC5T] 0.4 0.3 0.2 0 SUPPLY VOLTAGE : Vcc [V] Fig.1 Circuit Current 6 [BA50JC5T 0.5 1 1.5 2 2.5 OUTPUT CURRENT : I [A] OUT Fig.4 Load Stability 10 9 [BA50JC5T -40 - 100 TEMPERATURE : Ta [℃] Fig ...
Page 5
... OUT ADJ pin C External capacit setting range Approximately 0.33 F 22 F to 1000 F * For the BA00JC5WT, connect R1 and R2 externally between the ADJ and GND pins and between the OUT and ADJ pins. OUT Equation: VOUT = Vc ( (Vc = 1.25 V (Typ.)) The recommended R1 value is approximately 30 k ...
Page 6
... BA□□JC5 Series,BA00JC5WT Thermal Derating Curve TO220FP-3/TO220FP-5/TO220FP-5 (V5) 25 (1) When using an infinite heat sink. j-c = 6.25 (°C/W) (1)20.0 (2) During IC without heat sink operation. 20 j-a = 62.5 (°C/ (2)2 AMBIENT TEMPERATURE:Ta [ Fig.17 The characteristics of the IC are greatly influenced by the operating temperature. If the temperature exceeds the maximum , deterioration or damage may occur ...
Page 7
... BA□□JC5 Series,BA00JC5WT Operation Notes Vcc pin Insert a capacitor (0.33 F approx.) between VCC and GND. The capacitance will vary depending on the application. Use a suitable capacitance and implement designs with sufficient margins. GND pin Verify that there is no potential difference between the ground of the application board and the IC. ...
Page 8
... BA□□JC5 Series,BA00JC5WT Notes for use 1. Absolute maximum ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses ...
Page 9
... BA□□JC5 Series,BA00JC5WT ●Ordering part number Part number Current capacity Output voltage 1.5A 00:Variable Other:Fixed TO220FP-3 +0.3 10.0 −0.1 4.5 +0.3 7.0 −0.1 φ3.2±0.1 1.3 0.8 +0.1 0.55 −0.05 2.54±0.5 2.54±0 TO220FP-5 +0.3 10.0 −0.1 4.5 +0.3 φ 3.2±0.1 7.0 − ...
Page 10
... BA□□JC5 Series,BA00JC5WT TO220FP-5(V5) + 0.3 +0.3 10.0 − 0.1 4.5 −0.1 + 0.3 φ 3.2±0.1 7.0 − 0.1 1.2 0.8 0.5±0.1 4.25 1.778 8. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. <Tape and Reel information> Container Tube +0.2 −0.1 2.8 ...
Page 11
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose ...