LT1963AEST-1.5 Linear Technology, LT1963AEST-1.5 Datasheet - Page 17
![IC REG LDO LN 1.5A 1.5V SOT223-3](/photos/7/35/73514/sot-223-3_05-08-1630_sml.jpg)
LT1963AEST-1.5
Manufacturer Part Number
LT1963AEST-1.5
Description
IC REG LDO LN 1.5A 1.5V SOT223-3
Manufacturer
Linear Technology
Datasheet
1.LT1963AEST-3.3TRPBF.pdf
(28 pages)
Specifications of LT1963AEST-1.5
Regulator Topology
Positive Fixed
Voltage - Output
1.5V
Voltage - Input
2.1 ~ 20 V
Voltage - Dropout (typical)
0.34V @ 1.5A
Number Of Regulators
1
Current - Output
1.5A
Current - Limit (min)
1.6A
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
SOT-223 (3 leads + Tab), SC-73, TO-261
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT1963AEST-1.5
Manufacturer:
Linear Technology
Quantity:
1 823
Part Number:
LT1963AEST-1.5
Manufacturer:
LT/凌特
Quantity:
20 000
Company:
Part Number:
LT1963AEST-1.5#PBF
Manufacturer:
LT
Quantity:
10 439
Company:
Part Number:
LT1963AEST-1.5#PBF
Manufacturer:
Linear
Quantity:
28
Company:
Part Number:
LT1963AEST-1.5#PBF
Manufacturer:
LINEAR42
Quantity:
1 168
Company:
Part Number:
LT1963AEST-1.5#TRPBF
Manufacturer:
LT
Quantity:
10 439
Part Number:
LT1963AEST-1.5#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIONS INFORMATION
Y5V dielectrics are good for providing high capacitances in
a small package, but exhibit strong voltage and temperature
coefficients as shown in Figures 10 and 11. When used
with a 5V regulator, a 10µF Y5V capacitor can exhibit an
effective value as low as 1µF to 2µF over the operating
temperature range. The X5R and X7R dielectrics result in
more stable characteristics and are more suitable for use
as the output capacitor. The X7R type has better stability
across temperature, while the X5R is less expensive and
is available in higher values.
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or micro-
phone works. For a ceramic capacitor the stress can be
induced by vibrations in the system or thermal transients.
Figure 10. Ceramic Capacitor DC Bias Characteristics
–100
–20
–40
–60
–80
20
0
0
2
Table 2. PC Trace Resistors
4
0.5oz C
1.0oz C
2.0oz C
DC BIAS VOLTAGE (V)
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
6
U
U
U
8
Y5V
X5R
10
12
Length
Length
Length
Width
Width
Width
14
1963A F10
16
0.011
0.006
0.006
0.102
0.110
0.224
10mΩ
"
"
"
"
"
"
(0.28mm)
(0.15mm)
(0.15mm)
(2.6mm)
(2.8mm)
(5.7mm)
“FREE” Resistance with PC Traces
The resistance values shown in Table 2 can easily be made
using a small section of PC trace in series with the output
capacitor. The wide range of non-critical ESR makes it
easy to use PC trace. The trace width should be sized to
handle the RMS ripple current associated with the load.
The output capacitor only sources or sinks current for a few
microseconds during fast output current transitions. There
is no DC current in the output capacitor. Worst case ripple
current will occur if the output load is a high frequency
(>100kHz) square wave with a high peak value and fast
edges (< 1µs). Measured RMS value for this case is 0.5
times the peak-to-peak current change. Slower edges or
lower frequency will significantly reduce the RMS ripple
current in the capacitor.
Figure 11. Ceramic Capacitor Temperature Characteristics
0.011
0.006
0.006
0.450
0.204
0.220
20mΩ
"
"
"
"
"
"
(0.28mm)
(0.15mm)
(0.15mm)
(11.4mm)
(5.2mm)
(5.6mm)
–100
–20
–40
–60
–80
40
20
0
–50
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
–25
0.011
0.006
0.006
0.307
0.330
0.670
0
TEMPERATURE (°C)
30mΩ
"
"
"
"
"
"
(0.28mm)
(0.15mm)
(0.15mm)
LT1963A Series
25
(7.8mm)
(8.4mm)
(17mm)
50
Y5V
75
X5R
100
1963A F11
125
17
1963afe