LT3008ITS8#TRMPBF Linear Technology, LT3008ITS8#TRMPBF Datasheet - Page 6
![IC REG LDO ADJ 20MA TSOT23-8](/photos/6/59/65931/tsot-23-8_05-08-1637_sml.jpg)
LT3008ITS8#TRMPBF
Manufacturer Part Number
LT3008ITS8#TRMPBF
Description
IC REG LDO ADJ 20MA TSOT23-8
Manufacturer
Linear Technology
Datasheet
1.LT3008EDCTRMPBF.pdf
(20 pages)
Specifications of LT3008ITS8#TRMPBF
Regulator Topology
Positive Adjustable
Voltage - Output
0.6 ~ 44.5 V
Voltage - Input
2 ~ 45 V
Voltage - Dropout (typical)
0.3V @ 20mA
Number Of Regulators
1
Current - Output
20mA
Current - Limit (min)
22mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TSOT-23-8, TSOT-8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LT3008 Series
PARAMETER
Current Limit
Input Reverse-Leakage Current
Reverse-Output Current
ELECTRICAL CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3008 regulators are tested and specifi ed under pulse load
conditions such that T
Performance at – 40°C and 125°C is assured by design, characterization
and correlation with statistical process controls. The LT3008I is guaran-
teed over the full – 40°C to 125°C operating junction temperature range.
The LT3008MP is 100% tested and quaranteed over the –55°C to 125°C
operating junction temperature range.
Note 3: The LT3008 adjustable version is tested and specifi ed for these
conditions with the ADJ pin connected to the OUT pin.
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specifi cation will not apply
for all possible combinations of input voltage and output current. When
operating at the maximum input voltage, the output current range must be
limited. When operating at the maximum output current, the input voltage
must be limited.
6
temperature range, otherwise specifi cations are at T
J
≅ T
A
. The LT3008E is 100% tested at T
CONDITIONS
V
V
V
V
IN
IN
IN
OUT
= 45V, V
= V
= –45V, V
= 1.2V, V
J
OUT(NOMINAL)
A
= 25°C. (Note 2)
=25°C.
OUT
OUT
The
IN
= 0
= 0
= 0
l
+ 1V, ΔV
denotes the specifi cations which apply over the full operating
Note 5: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specifi ed output current. In dropout, the
output voltage equals (V
1.5, dropout voltage will be limited by the minimum input voltage.
Note 6: To satisfy minimum input voltage requirements, the LT3008
adjustable version is tested and specifi ed for these conditions with an
external resistor divider (61.9k bottom, 280k top) which sets V
The external resistor divider adds 9.69μA of DC load on the output. This
external current is not factored into GND pin current.
Note 7: GND pin current is tested with V
a current source load. GND pin current will increase in dropout. For the
fi xed output voltage versions, an internal resistor divider will add about
1μA to the GND pin current. See the GND Pin Current curves in the Typical
Performance Characteristics section.
Note 8: The SHDN pin can be driven below GND only when tied to the IN
pin directly or through a pull-up resistor. If the SHDN pin is driven below
GND by more than –0.3V while IN is powered, the output will turn on.
Note 9: Output noise is listed for the adjustable version with the ADJ pin
connected to the OUT pin. See the RMS Output Noise vs Load Current
curve in the Typical Performance Characteristics Section.
OUT
= – 5%
IN
– V
l
l
DROPOUT
MIN
22
). For the LT3008-1.2 and LT3008-
IN
= V
OUT(NOMINAL)
TYP
0.6
75
1
MAX
30
10
+ 0.55V and
OUT
to 3.3V.
UNITS
3008fb
mA
mA
μA
μA