MIC68200-1.5YML TR Micrel Inc, MIC68200-1.5YML TR Datasheet
MIC68200-1.5YML TR
Specifications of MIC68200-1.5YML TR
MIC68200-1.5YMLTR
MIC68200-1.5YMLTR
Related parts for MIC68200-1.5YML TR
MIC68200-1.5YML TR Summary of contents
Page 1
... General Description The MIC68200 is a high peak current LDO regulator designed specifically for powering applications such as FPGA core voltages that require high start up current with lower nominal operating current. Capable of sourcing 2A of current for start-up, the MIC68200 provides high power from a small MLF package ...
Page 2
... U1.OUT U2.EN= U1.POR U2.RC U2.DLY U2.OUT U2.POR Sequenced Dual Power Supply for I/O and Core Voltage of µProcessor February 2011 MIC68200-1.8YML U1 IN OUT EN SNS Master RC DLY GND POR MIC68200-1.5YML U2 IN OUT EN SNS Slave RC DLY GND POR U1.T DLY RC U2.T RC U2.T DLY 2 2x μ ...
Page 3
... U2.RC=U1.OUT U2.DLY U2.OUT U1.POR=U2.POR Tracking Dual Power Supply for I/O and Core Voltage of µProcessor February 2011 47KΩ MIC68200-1.5YML U1 IN OUT EN Master RC DELAY GND POR MIC68200-1.2YML U2 IN OUT EN Slave RC DELAY GND POR U2.T DLY 3 μProcessor I/O 4.7µF CORE 4.7µF ...
Page 4
... Marking Part Number Code MIC68200-1.2YML ZC12 MIC68200-1.5YML ZC15 MIC68200-1.8YML ZC18 MIC68200-2.5YML ZC25 MIC68200-3.3YML ZC33 MIC68200YML ZAAA Notes : * For additional voltage options, contact Micrel Marketing. ® ** MLF is a GREEN RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free. February 2011 Output ...
Page 5
... EP 6 10-Pin 3mm × 3mm MLF (ML) MIC68200-x.xYML (Fixed) MIC68200YML (Adjustable) Pin Name Pin Function IN Input: Input voltage supply pin. Place a capacitor to ground to bypass the input supply DLY Delay: Capacitor to ground sets internal delay timer. Timer delays power-on reset (POR) output at turn-on and ramp down at turn-off. ...
Page 6
Absolute Maximum Ratings Supply Voltage (V ) ................................................ 6V IN Enable Input Voltage (V )..................... POR (V )...................................................V POR RC ...............................................................V Power Dissipation...........................Internally Limited Junction Temperature ................ –40°C ≤ T Storage Temperature (T ) .......... –65°C ...
Page 7
Electrical Characteristics T = 25°C with 1V OUT Parameter Ramp Control (Note 7) DISCHARGE(OUTPUT) Tracking Accuracy: Fixed (Note 8) Tracking Accuracy: Adjustable (Note 8) Notes: 1. Exceeding the absolute maximum ...
Page 8
Typical Characteristics Ground Current vs. Output Current =1.8V out +1V in out C =10μF 5 out 0 0.0 0.5 1.0 1.5 Output Current (A) Ground Current vs. Temperature 45 ...
Page 9
... V = 2.5V OUT I = 500mA OUT 10 0 1000 0.01 0 FREQUENCY (kHz) MIC68200 PSRR V = 1.8V 500mA IN OUT 1. 1.2V OUT I = 500mA OUT 10 0 1000 0.01 0 FREQUENCY (kHz) 9 MIC68200 PSRR V = 3.8V 3. 3.3V OUT OUT 10 0 100 1000 0.01 0.1 1 FREQUENCY (kHz) MIC68200 PSRR V = 3.3V 3. 2.5V OUT ...
Page 10
Functional Characteristics February 2011 10 M9999-022311-E ...
Page 11
... In shutdown the regulator consumes very little current (only a few microamperes of leakage). For simple applications the enable (EN) can be connected to V MIC68200 only requires a few µA’s of enable current to turn on, actual enable pin current will depend on the overdrive (voltage exceeding 1V) in each particular application. ...
Page 12
... Fixed Parts driven from another (Master) regulator the two outputs will track each other until the Master exceeds the target voltage of the Slave regulator. Typically the output of the MIC68200 will track above the RC input by 30mV to 70mV. This offset is designed to allow Master/Slave tracking of same-voltage regulators ...
Page 13
... RC pin for low values of output capacitor the maximum discharge current available at the output for large values of output capacitor. Turn off slew rate is not a specified characteristic of the MIC68200. Sequencing Configurations Sequencing refers to timing based Master/Slave control between regulators. It allows a Master device to control the start and stop timing of a single or multiple Slave devices ...
Page 14
... DLY GND POR February 2011 Fixed voltage versions of MIC68200 have two internal voltage dividers: one for setting the output voltage and the other for driving the tracking circuitry. Adjustable parts have up to two external dividers: one from output to SNS (to set the output voltage) and one from the output to the Slave RC pin (in tracking configurations) ...
Page 15
... POR Final Note on Tracking The MIC68200 does not fully shutdown until the output load is discharged to near zero driven from an external source in a tracking configuration, and the external source does not go to zero on shutdown it may prevent complete shutdown of the MIC68200. This will cause no damage, but some Q current will remain and may cause concern in battery operated portable equipment ...
Page 16
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully February 2011 10-Pin 3mm x 3mm MLF (ML) indemnify Micrel for any damages resulting from such use or sale. © 2005 Micrel, Incorporated. 16 MIC68200 http://www.micrel.com M9999-022311-E ...