60R090XU Littelfuse Inc, 60R090XU Datasheet - Page 3

• Manufacturer Part Number: 60R090XU
• Description: PTC .90A 60V RESETTABLE KINK
• Manufacturer: Littelfuse Inc
• Series: POLYFUSE® 60Rr

Specifications of 60R090XU

• R Min/max: 0.200 ~ 0.470 Ohm
• Voltage - Max: 60V
• Time To Trip: 7.2s
• Current - Hold (ih) (max): 900mA
• Current - Trip (it): 1.8A
• Current - Max: 40A
• Package / Case: Radial
• Hold Current: 0.9 Amp
• Trip Current: 1.8 Amps
• Current Rating (max): 40 Amps
• Resistance: 0.47 Ohms
• Maximum Voltage: 60 VoltsDC
• Termination Style: Radial
• Mounting Style: Through Hole
• Current Rating: 40 Amps
• Dimensions: 11.2 mm D
• Lead Spacing: 5.08 mm
• Operating Temperature Range: - 40 C to + 85 C
• Initial Resistance (min): 200mOhm
• Voltage Rating Max: 60VDC
• Trip Time (max): 7.2@4.5As
• Power Dissipation (typ): 0.99W
• Post Trip Resistance (max): 470mOhm
• Agency Approvals: CULUS/TUV
• Operating Temperature Min Deg. C: -40C
• Operating Temperature Max Deg. C: 85C
• Holding Current: 0.9mA
• Tripping Current: 1.8A
• Initial Resistance Max: 0.47ohm
• Operating Voltage: 60VDC
• Ptc Fuse Case: Radial Leaded
• Operating Temperature Max: 85°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 060R0090; 060R0090U; 60R090; F2009

Specifications are subject to change without notice.
Please refer to www.littelfuse.com/series/60R.html for current information.
©2008 Littelfuse, Inc.
©2008 Littelfuse, Inc.
Soldering Parameters - Wave Soldering
Pre-Heating Zone
Soldering Zone
Cooling Zone
Physical Specifications
Lead Material
Soldering
Characteristics
Insulating Material
Device Labeling
.20-.40A: Tin-plated Copper clad steel
.50-3.75A: Tin-plated Copper
Solderability per MIL–STD–202,
Method 208E
Cured, flame retardant epoxy polymer
meets UL94V-0 requirements.
Marked with ‘LF’, voltage, current rating,
and date code.
Refer to the condition
recommended by the
flux manufacturer.
Max. ramping rate
should not exceed 4°C/
Sec.
Max. solder
temperature should not
exceed 260°C
Cooling by natural
convection in air.
Radial Leaded > 60R Series
POLYFUSE
Revised: October 24, 2008
®
Resettable PTCs
Operating/Storage
Temperature
Maximum Device Surface
Temperature in Tripped State
Passive Aging
Humidity Aging
Thermal Shock
Solvent Resistance
Moisture Resistance Level
Environmental Specifications
260
220
190
160
0
Preheating
60 min.
Soldering
-40°C to +85°C
125°C
+85°C, 1000 hours
-/+ 5% typical resistance
change
+85°C, 85% R.H.,1000 hours
-/+ 5% typical resistance
change
+85°C to -40°C 10 times
-/+ 5% typical resistance
change
MIL–STD–202, Method 215F
Level 2, J–STD–020C
5 max.
Time(s)
Cooling
60R Series