LP38690SD-ADJ/NOPB National Semiconductor, LP38690SD-ADJ/NOPB Datasheet - Page 5
![IC REG LDO 1A ADJ 6-LLP](/photos/6/93/69397/pkg_sde06a_sml.jpg)
LP38690SD-ADJ/NOPB
Manufacturer Part Number
LP38690SD-ADJ/NOPB
Description
IC REG LDO 1A ADJ 6-LLP
Manufacturer
National Semiconductor
Series
PowerWise®r
Datasheet
1.LP38690SD-ADJNOPB.pdf
(16 pages)
Specifications of LP38690SD-ADJ/NOPB
Regulator Topology
Positive Adjustable
Voltage - Output
1.25 ~ 9 V
Voltage - Input
2.7 ~ 10 V
Voltage - Dropout (typical)
0.45V @ 1A
Number Of Regulators
1
Current - Output
1A
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
6-LLP
Number Of Outputs
1
Polarity
Positive
Input Voltage Max
10 V
Output Voltage
1.25 V to 9 V
Output Type
Adjustable
Dropout Voltage (max)
1.6 V At 1 A
Output Current
1 A
Line Regulation
0.03 %/V
Load Regulation
1.8 %/A
Voltage Regulation Accuracy
+/- 2.5 %
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / Rohs Status
Details
Other names
LP38690SD-ADJ
LP38690SD-ADJTR
LP38690SD-ADJTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LP38690SD-ADJ/NOPB
Manufacturer:
NS/国半
Quantity:
20 000
e
V
V
I
EN
n
O
EN
Symbol
Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications, see Electrical Characteristics. Specifications do not
apply when operating the device outside of its rated operating conditions.
Note 2: At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink values (if a heatsink is used).
The junction-to-ambient thermal resistance (θ
copper area (less than 0.1 square inch). If one square inch of copper is used as a heat dissipator for the SOT-223, the θ
θ
the
shutdown.
Note 3: ESD is tested using the human body model which is a 100pF capacitor discharged through a 1.5k resistor into each pin.
Note 4: Typical numbers represent the most likely parametric norm for 25°C operation.
Note 5: If used in a dual-supply system where the regulator load is returned to a negative supply, the output pin must be diode clamped to ground.
Note 6: Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage.
Note 7: Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from 1mA to full load.
Note 8: Dropout voltage is defined as the minimum input to output differential required to maintain the output within 100mV of nominal value.
J-A
(LEAK)
LLP MOUNTING
values for the LLP package are also dependent on trace area, copper thickness, and the number of thermal vias used (refer to application note AN-1187 and
Output Noise
Output Leakage Current
Enable Voltage (LP38692-ADJ
Only)
Enable Pin Leakage (LP38692-
ADJ Only)
section in this datasheet). If power disspation causes the junction temperature to exceed specified limits, the device will go into thermal
Parameter
J-A
) for the SOT-223 is approximately 125 °C/W for a PC board mounting with the device soldered down to minimum
BW = 10Hz to 10kHz
V
V
Output = OFF
Output = ON, V
Output = ON, V
Output = ON, V
V
O
O
EN
= 3.3V
= V
= 0V or 10V, V
O
(NOM) + 1V @ 10V
Conditions
IN
IN
IN
5
= 4V
= 6V
= 10V
IN
= 10V
IN
Min
1.8
3.0
4.0
-1
J-A
drops to approximately 70 °C/W. The
(Note
0.001
Typ
0.7
0.5
4)
Max
0.4
2
1
www.national.com
µV/
Units
µA
µA
V