SC1453ISK18TRT Semtech, SC1453ISK18TRT Datasheet
SC1453ISK18TRT
Specifications of SC1453ISK18TRT
SC1453ISK18TR
Related parts for SC1453ISK18TRT
SC1453ISK18TRT Summary of contents
Page 1
... Surface mount packaging (5 pin SOT-23 and TSOT-23) Available in Lead-free packages, fully WEEE and RoHS compliant Applications Battery Powered Systems Cellular Telephones Cordless Telephones Personal Digital Assistants Portable Instrumentation Modems PCMCIA cards U1 SC1453 OUT BYP GND 2 C2 10nF 1 SC1453 = C = 1µ 10nF) OUT BYP VOUT C3 1uF www.semtech.com ...
Page 2
... Exceeding the specifications below may result in permanent damage to the device, or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not implied Electrical Characteristics Unless specified 1V OUT EN IN OUT 2008 Semtech Corp 100µ 1µ 25°C. Values in bold apply over full operating ambient temperature range. IN OUT SC1453 www.semtech.com ° ° ° C ° C ° C ° ...
Page 3
... IN(MIN) (3) Defined as the input to output differential at which the output voltage drops 100mV below the value measured at a differential of 1V. Not measurable on 1.5V and 1.8V parts due to minimum V (4) Guaranteed by design. 2008 Semtech Corp. = 100µ 1µ 25°C. Values in bold apply over full operating ambient temperature range. ...
Page 4
... NOT RECOMMENDED FOR NEW DESIGN POWER MANAGEMENT Pin Configuration Top View (SOT-23-5 & TSOT-23-5) Pin Descriptions 2008 Semtech Corp SC1453 www.semtech.com ...
Page 5
... Only available in tape and reel packaging. A reel contains 3000 devices. (2) Lead free packaging (ordered with suffix extension “TRT”) is optional. Consult factory for availability. This product is fully WEEE and RoHS compliant. (3) Evaluation board for SC1453. Specify output voltage option when ordering. 2008 Semtech Corp ...
Page 6
... XX = voltage option (examples: 5331 for 3.1V option in SOT-23-5 Top Mark BX00 For SC1453, 2.85V option for SOT-23-5 and N for TSOT-23-5 Block Diagram 2008 Semtech Corp. Bottom Mark yyww yyww = Date code (example: 0008 for week 8 of 2000) Bottom Mark yyww yyww = Date code ...
Page 7
... Increasing the bulk capacitance will further reduce output noise and improve the overall transient response. Input capacitor - Semtech recommends the use of a 1µF ceramic capacitor at the input. This allows for the device being some distance from any bulk capacitance on the rail ...
Page 8
... SOT-23-5 package. The use of multi layer boards with internal ground/power planes will lower the junction temperature and improve overall output voltage accuracy. 2008 Semtech Corp. Layout Considerations While layout for linear devices is generally not as critical mW as for a switching application, careful attention to detail will ensure reliable operation. 125° ...
Page 9
... OUT -0.30 -50 - (°C) J Load Regulation vs. Junction Temperature OUT 0.1mA to 150mA OUT -50 - (°C) J 2008 Semtech Corp. 200 6. 175 V EN 150 125 V = 3.8V IN 100 100 125 -50 Line Regulation vs. Junction Temperature 12 I OUT 100 125 -50 Current Limit vs. Junction Temperature 0.90 0.85 0.80 0.75 0.70 ...
Page 10
... Junction Temperature 5 -6. 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -50 - (°C) J 2008 Semtech Corp. Dropout Voltage vs. Output Current 200 175 150 I = 150mA OUT 125 100 50mA OUT 100 125 0 Enable Input Threshold Voltage vs. Junction Temperature vs. Input Voltage 1.6 1.4 ...
Page 11
... OUT 1µF IN OUT 3.0V OUT C = 10nF BYP V = 3.3V OUT I = 1mA 10 OUT T = 25° 0.01 0 (kHz) 2008 Semtech Corp. Output Spectral Noise Density vs. Frequency = 100µ OUT I = 1mA OUT C = 1µ 10nF BYP T = 25°C J 0.1 0.01 0.001 10 100 1000 0.01 Output Spectral Noise Density vs. Frequency ...
Page 12
... NOT RECOMMENDED FOR NEW DESIGN POWER MANAGEMENT Evaluation Board Schematic J2 IN MON J10 J11 J12 J13 J14 J15 GND GND GND GND GND GND Evaluation Board Bill of Materials 2008 Semtech Corp. U1 SC1453 1 5 OUT BYP EN GND MON J16 LOAD DRV µ ...
Page 13
... NOT RECOMMENDED FOR NEW DESIGN POWER MANAGEMENT Evaluation Board Gerber Plots Top Copper Top Silk Screen 2008 Semtech Corp. Bottom Copper SC1453 www.semtech.com ...
Page 14
... DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS 3. OR GATE BURRS. Land Pattern - SOT-23-5 X (C) P NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 2008 Semtech Corp. A DIM MIN NOM .035 A1 .000 A2 .035 N ...
Page 15
... REFERENCE JEDEC STD MO-193, VARIATION AB. Land Pattern - TSOT-23-5 X (C) P NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. Contact Information Phone: (805)498-2111 FAX (805)498-3804 2008 Semtech Corp. DIMENSIONS INCHES DIM A MIN NOM - ...