TC1016-1.85VCTTR Microchip Technology, TC1016-1.85VCTTR Datasheet - Page 10
![IC REG LDO 1.85V SOT-23-5](/photos/6/59/65927/mfg_mcp402x_sot-23-5_sml.jpg)
TC1016-1.85VCTTR
Manufacturer Part Number
TC1016-1.85VCTTR
Description
IC REG LDO 1.85V SOT-23-5
Manufacturer
Microchip Technology
Specifications of TC1016-1.85VCTTR
Regulator Topology
Positive Fixed
Voltage - Output
1.85V
Voltage - Input
2.7 ~ 6 V
Voltage - Dropout (typical)
0.15V @ 80mA
Number Of Regulators
1
Current - Output
80mA (Min)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
SOT-23-5, SC-74A, SOT-25
Primary Input Voltage
6V
Output Voltage Fixed
1.85V
Dropout Voltage Vdo
150mV
No. Of Pins
5
Output Current
80mA
Operating Temperature Range
-40°C To +125°C
Voltage Regulator Case Style
SOT-23
Svhc
No
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TC1016-1.85VCTTR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
TC1016
4.1
Low input source impedance is necessary for the LDO
to operate properly. When operating from batteries, or
in applications with long lead length (> 10") between
the input source and the LDO, some input capacitance
is required. A minimum of 0.1 µF is recommended for
most applications and the capacitor should be placed
as close to the input of the LDO as is practical. Larger
input capacitors will help reduce the input impedance
and further reduce any high-frequency noise on the
input and output of the LDO.
4.2
A minimum output capacitance of 1 µF for the TC1016
is required for stability. The ESR requirements on the
output capacitor are between 0 and 2 ohms. The output
capacitor should be located as close to the LDO output
as is practical. Ceramic materials X7R and X5R have
low temperature coefficients and are well within the
acceptable ESR range required. A typical 1 µF X5R
0805 capacitor has an ESR of 50 milli-ohms. Larger
output capacitors can be used with the TC1016 to
improve dynamic behavior and input ripple rejection
performance.
Ceramic, aluminum electrolytic or tantalum capacitor
types can be used. Since many aluminum electrolytic
capacitors freeze at approximately –30 C, ceramic or
solid tantalums are recommended for applications
operating below –25 C. When operating from sources
other than batteries, supply noise rejection and tran-
sient response can be improved by increasing the
value of the input and output capacitors, and by
employing passive filtering techniques.
FIGURE 4-3:
DS21666B-page 10
Input Capacitor
Output Capacitor
SHDN
V
Wake-Up Time from Shutdown.
OUT
V
IL
4.3
The turn on response is defined as two separate
response categories, Wake-up Time (t
Time (t
The TC1016 has a fast t
released from shutdown. Figure 4-3 provides the
TC1016’s t
for the output to rise to 2% of the V
released from shutdown.
The total turn-on response is defined as the t
Figure 4-3). The t
condition when the output is within 98% of its fully
enabled value (42 µsec, typ.) when released from shut-
down. The settling time of the output voltage is
dependent on load conditions and output capacitance
on V
Table 4-1 demonstrates the typical turn-on response
timing for different input voltage power-up frequencies:
V
TABLE 4-1:
OUT
Frequency
OUT
1000 Hz
500 Hz
100 Hz
= 2.8V, V
50 Hz
10 Hz
S
2%
).
Turn-On Response
(RC response).
WK
t
WK
V
98%
. The t
IH
IN
= 5.0V, I
S
TYPICAL TURN-ON
RESPONSE TIMING
(inclusive with t
t
S
WK
Typical (t
14.5 µsec
17.2 µsec
5.3 µsec
5.9 µsec
9.8 µsec
© 2005 Microchip Technology Inc.
is defined as the time it takes
OUT
WK
= 60 mA and C
WK
(10 µsec, typ.) when
)
OUT
WK
) is defined as the
value after being
WK
Typical (t
) and Settling
14 µsec
16 µsec
32 µsec
52 µsec
77 µsec
OUT
= 1 µF.
S
S
(see
)