MC33161D ON Semiconductor, MC33161D Datasheet - Page 5

• Manufacturer Part Number: MC33161D
• Description: IC VOLTAGE MONITOR UNIV 8-SOIC
• Manufacturer: ON Semiconductor
• Type: Multi-Voltage Supervisorr

Specifications of MC33161D

• Number Of Voltages Monitored: 2
• Output: Open Drain or Open Collector
• Voltage - Threshold: Adjustable/Selectable
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Reset: -
• Reset Timeout: -

supervisory circuit containing many of the necessary
monitoring functions required in microprocessor based
systems. It is specifically designed for appliance and
industrial applications, offering the designer a cost effective
solution with minimal external components. These devices
are specified for operation over an input voltage of 7.0 V to
40 V, and with a junction temperature of −40° to +150°C. A
typical microprocessor application is shown in Figure 11.
Regulator
100 mA output current and is short circuit protected. The
output has a guaranteed tolerance of ±5.0% over line, load,
and temperature. Internal thermal shutdown circuitry is
included to limit the maximum junction temperature to a
safe level. When activated, typically at 170°C, the
regulator output turns off.
bypass capacitors may be required for regulator stability. If
the regulator is located an appreciable distance (≥ 4″) from
the supply filter, an input bypass capacitor (C
or greater is suggested. Output capacitance values of less
than 5.0 nF may cause regulator instability at light load
(≤ 1.0 mA) and cold temperature. An output bypass
PIN FUNCTION DESCRIPTION
The MC34160 series is a monolithic voltage regulator and
The 5.0 V regulator is designed to source in excess of
In specific situations a combination of input and output
4, 5, 12, 13
Pin
10
14
15
16
11
1
2
3
6
7
8
9
Comparator Inverting
Input
Comparator Noninverting
Input
N.C.
GND
Comparator Output
Reset
Power Warning
Power Sense
Hysteresis Adjust
Regulator Output
V
Chip Disable
V
CC
ref
Function
This is the Uncommitted Comparator Inverting input. It is typically connected to a resistor
divider to monitor a voltage.
This is the Uncommitted Comparator Noninverting input. It is typically connected to a
reference voltage.
No connection. This pin is not internally connected.
These pins are the control circuit grounds and are connected to the source and load ground
returns. They are part of the IC lead frame and can be used for heatsinking.
This is the Uncommitted Comparator output. It is an open collector sink−only output requiring
a pullup resistor.
This is the Reset Comparator output. It is an open collector sink−only output requiring a
pullup resistor.
This is the Power Warning Comparator output. It is an open collector sink−only output
requiring a pullup resistor.
This is the Power Warning Comparator noninverting input. It is typically connected to a
resistor divider to monitor the input power source voltage.
The Power Warning Comparator hysteresis is programmed by a resistor connected from this
pin to ground.
This is the 5.0 V Regulator output.
This pin is the positive supply input of the control IC.
This input is used to switch the IC into a standby mode turning off all outputs.
This is the 2.6 V Reference output. It is intended to be used in conjunction with the Power
Warning and Uncommitted comparators.
OPERATING DESCRIPTION
in
) of 0.33 mF
MC34160, MC33160
http://onsemi.com
5
capacitor of 0.1 mF or greater is recommended to ensure
stability under all load conditions. The capacitors selected
must provide good high frequency characteristics.
minimize ground loops and lead resistance drops since the
regulator does not have external sense inputs.
Reference
and has a guaranteed output tolerance of ±5.0% over line,
load, and temperature. It is intended to be used in
conjunction with the Power Warning and Uncommitted
comparator. The reference can source in excess of 2.0 mA
and sink a maximum of 10 mA. For additional current
sinking capability, an external load resistor to ground must
be used.
or V
nominal.
Chip Disable
When activated, internal biasing for the entire die is
removed causing all outputs to turn off. This reduces the
power supply current (I
Good construction techniques should be used to
The 2.6 V bandgap reference is short circuit protected
Reference biasing is internally derived from either V
This input is used to switch the IC into a standby mode.
O
, allowing proper operation if either drops below
Description
CC
) to less than 0.3 mA.
CC