X40626V14-2.7T1 Intersil, X40626V14-2.7T1 Datasheet - Page 15

• Manufacturer Part Number: X40626V14-2.7T1
• Description: IC SUPERVISOR CPU DUAL 14-TSSOP
• Manufacturer: Intersil
• Type: Multi-Voltage Supervisorr

Specifications of X40626V14-2.7T1

• Number Of Voltages Monitored: 2
• Output: Open Drain or Open Collector
• Reset: Active Low
• Reset Timeout: 100 ms Minimum
• Voltage - Threshold: 2.63V, 2.63V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

ABSOLUTE MAXIMUM RATINGS
Temperature under bias ................... -65°C to +135°C
Storage temperature ........................ -65°C to +150°C
Voltage on any pin with respect to VSS... -1.0V to +7V
D.C. output current (sink) ................................... 10mA
Lead temperature (soldering, 10 seconds) ........ 300°C
Table 2. Recommended Operating Conditions
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Notes: (1) The device enters the Active state after any start, and remains active until: (a) 9 clock cycles later if the Device Select Bits in the Slave
I
I
I
I
I
I
V
V
V
V
Symbol
CC1
CC2
SB1
SB2
LI
LO
IL
IH
HYS
OL
Commercial
Industrial
(2)
(3)
(1)
(2)
Temp
(2) The device enters the Active state after any start, and remains active until t
(3) The device goes into Standby: (a) 200nS after any stop, except those that initiate a nonvolatile write cycle; or (b) t
Address Byte are incorrect; or (b) 200nS after a stop ending a read operation.
initiates a nonvolatile cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in the Slave Address
Byte.
Active Supply Current Read
Active Supply Current Write
Standby Current DC (WDT off)
Standby Current DC (WDT on)
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Schmitt Trigger Input Hysteresis
Output LOW Voltage
Parameter
-40°C
Min.
0°C
15
V
Fixed input level
CC
related level
+85°C
Max.
70°C
V
.05 x V
CC
V
Min
0.2
-1
CC
x 0.7
X40626
CC
= 2.7 to 5.5V
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.
V
V
CC
CC
Max
1.0
3.0
0.4
30
10
10
1
x 0.3
+0.5
WC
after a stop ending a write operation.
Unit
mA
mA
µA
µA
µA
µA
V
V
V
V
V
V
f
V
Others=GND or V
V
Others=GND or V
V
V
Device is in Standby
I
I
SCL
OL
OL
IL
SDA
SDA
IN
SDA
= V
= 1.0mA (V
= 3.0mA (V
= GND to V
= 400kHz, SDA = Open
=V
=V
= GND to V
CC
Test Conditions
SCL
SCL
x 0.1, V
=V
=V
CC
CC
CC
CC
CC
CC
=3V)
=5V)
CC
CC
IH
WC
= V
after a stop that
CC
March 28, 2005
x 0.9
FN8119.0