PTGL09AR390N0B52A0 Murata Electronics North America, PTGL09AR390N0B52A0 Datasheet - Page 86

THERM 39 OHM 250V PTC RADIAL

PTGL09AR390N0B52A0

Manufacturer Part Number
PTGL09AR390N0B52A0
Description
THERM 39 OHM 250V PTC RADIAL
Manufacturer
Murata Electronics North America
Series
PTGLr
Datasheet

Specifications of PTGL09AR390N0B52A0

Voltage - Max
250V
Current - Hold (ih) (max)
115mA
Current - Trip (it)
245mA
Current - Max
600mA
Package / Case
Radial
Lead Free Status / RoHS Status
Lead free by exemption / RoHS compliant by exemption
R Min/max
-
Time To Trip
-
Other names
490-4809-3
12
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Solder and Flux
2. Cleaning Conditions and Drying
3. Soldering Conditions
84
!Caution/Notice
Notice (Soldering and Mounting) PRG/PRF15 Series
(1) Solder Paste
To remove the flux after soldering, observe the following
points in order to avoid deterioration of the characteristics
or any change to the external electrodes quality.
(1) Cleaning Conditions
A sufficient cleaning should be applied to remove flux completely.
(2) Drying
In your mounting process, observe the following points in
order to avoid deterioration of the characteristics or
destruction of this product. The mounting quality of this
product may also be affected by the mounting conditions,
shown in the points below.
This product is for reflow soldering only. Flow soldering
should not be allowed.
(1) Printing Conditions of Solder Paste
(a) Standard thickness of solder paste printing should
(b) After soldering, the solder fillet should be a height
(c) Too much solder gives too strong mechanical stress
Use solder paste Sn:Pb=63:37wt%.
For your reference, we are using
manufactured by Alpha Metals Japan Ltd.
manufactured by Senju Metal Industry Co., LTD for any
Internal tests of this product.
After cleaning, promptly dry this product.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
be from 0.15 to 0.20 mm.
from 0.2 mm to the thickness of this product (see the
figure at right).
to this product. Such stress may cause cracking or
other mechanical damage. Also, it can destroy the
electrical performance of this product.
2-propanol
Solvent
63Sn/37Pb RMA9086 90-3-M18,
96.5Sn/3.0Ag/0.5Cu M705-GRN360-K2-V,
Less than 5 minutes
Less than 2 minutes
Dipping Cleaning
at room temp.
at 40˚C max.
or
Ultrasonic Cleaning
Less than 1 minute
20W/L Frequency
of several 10kHz
to 100kHz.
(2) Flux
E
• Strong acidic flux (with halide content exceeding
• Water-soluble flux
Use rosin type flux in soldering process.
If below flux is used, some problems might be caused
in the product characteristics and reliability.
Please do not use below flux.
0.2wt%).
(*Water-soluble flux can be defined as non rosin type
flux including wash-type flux and non-wash-type flux.)
Electrode
Solder
Continued on the following page.
T
Solder
0.2mm V T V E
R90E.pdf
10.3.4

Related parts for PTGL09AR390N0B52A0