MCP112-270E/TO Microchip Technology, MCP112-270E/TO Datasheet - Page 2
![IC VOLT DET 2.63V LOW TO92-3](/photos/7/50/75004/to-92_pkg_sml.jpg)
MCP112-270E/TO
Manufacturer Part Number
MCP112-270E/TO
Description
IC VOLT DET 2.63V LOW TO92-3
Manufacturer
Microchip Technology
Type
Simple Reset/Power-On Resetr
Datasheet
1.MCP112-270ETO.pdf
(26 pages)
Specifications of MCP112-270E/TO
Number Of Voltages Monitored
1
Output
Push-Pull, Totem Pole
Reset
Active Low
Voltage - Threshold
2.63V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-92-3 (Standard Body), TO-226
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Reset Timeout
-
MCP111/112
1.0
Absolute Maximum Ratings†
V
Input current (V
Output current (RST) . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
Rated Rise Time of V
All inputs and outputs (except RST) w.r.t. V
RST output w.r.t. V
Storage temperature . . . . . . . . . . . . . . . . . . . 65°C to + 150°C
Ambient temp. with power applied . . . . . . . -40°C to + 125°C
Maximum Junction temp. with power applied . . . . . . . . 150°C
ESD protection on all pins
DC CHARACTERISTICS
DS21889D-page 2
Electrical Specifications: Unless otherwise indicated, all limits are specified for V
T
Operating Voltage Range
Specified V
Operating Current
V
V
Note 1:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to (V
DD
A
DD
DD
= -40°C to +125°C.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0V
Trip Point
Trip Point Tempco
2:
3:
4:
ELECTRICAL
CHARACTERISTICS
DD
Trip point is ±1.5% from typical value.
Trip point is ±2.5% from typical value.
This specification allows this device to be used in PICmicro
Serial Programming™ (ICSP™) feature (see device-specific programming specifications for voltage requirements).
This specification DOES NOT allow a continuous high voltage to be present on the open-drain output pin (V
total time that the V
V
0°C to 70°C (+25°C preferred). For additional information, please refer to Figure 2-28.
This parameter is established by characterization and is not 100% tested.
OUT
Value to V
DD
Parameters
) . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
SS
pin should be limited to 2 mA. It is recommended that the device operational temperature be maintained between
DD
. . . . . . . . . . . . . . . . . . . -0.6V to 13.5V
. . . . . . . . . . . . . . . . . . . . . . 100V/µs
OUT
low
MCP1XX-195
MCP1XX-240
MCP1XX-270
MCP1XX-290
MCP1XX-300
MCP1XX-315
MCP1XX-450
MCP1XX-475
OUT
pin can be above the maximum device operational voltage (5.5V) is 100 sec. Current into the
SS
T
V
DD
Sym
V
V
TPCO
I
TRIP
DD
DD
DD
+ 1.0V)
2 kV
1.872
1.853
2.285
2.262
2.591
2.564
2.857
2.828
2.886
2.857
3.034
3.003
4.314
4.271
4.561
4.514
Min
1.0
1.0
—
—
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
®
microcontroller applications that require the In-Circuit
1.900
1.900
2.320
2.320
2.630
2.630
2.900
2.900
2.930
2.930
3.080
3.080
4.380
4.380
4.630
4.630
±100
Typ
< 1
—
—
DD
1.929
1.948
2.355
2.378
2.670
2.696
2.944
2.973
2.974
3.003
3.126
3.157
4.446
4.490
4.700
4.746
Max
1.75
5.5
—
= 1V to 5.5V, R
ppm/°
Units
µA
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
C
© 2005 Microchip Technology Inc.
I
T
T
T
Note 2
T
Note 2
T
Note 2
T
Note 2
T
Note 2
T
Note 2
T
Note 2
PU
RST
A
A
A
A
A
A
A
A
A
= +25°C (Note 1)
= -40°C to +85°C (Note 2)
= +25°C (Note 1)
= +25°C (Note 1)
= +25°C (Note 1)
= +25°C (Note 1)
= +25°C (Note 1)
= +25°C (Note 1)
= +25°C (Note 1)
= 100 k (only MCP111),
= 10 µA, V
Conditions
RST
OUT
< 0.2V
). The