MAX4076EUK+T Maxim Integrated Products, MAX4076EUK+T Datasheet - Page 11

• Manufacturer Part Number: MAX4076EUK+T
• Description: IC OPAMP FIXED GAIN R/R SOT23-5
• Manufacturer: Maxim Integrated Products
• Series: GainAmp™r

Specifications of MAX4076EUK+T

• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Slew Rate: 0.09 V/µs
• Gain Bandwidth Product: 230kHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 1200µV
• Current - Supply: 45µA
• Current - Output / Channel: 20mA
• Voltage - Supply, Single/dual (±): 2.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-5, SC-74A, SOT-25
• Number Of Channels: 1
• Voltage Gain Db: 117 dB
• Common Mode Rejection Ratio (min): 70 dB
• Input Offset Voltage: 1.2 mV
• Operating Supply Voltage: 3 V, 5 V
• Supply Current: 0.045 mA
• Maximum Power Dissipation: 571 mW
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Details

GainAmp fixed-gain amplifiers feature factory-trimmed
precision resistors to provide fixed inverting gains from
-0.25V/V to -100V/V or noninverting gains from +1.25V/V
to +101V/V. The op amp core is decompensated strate-
gically over the gain-set options to maximize band-
width. Open-loop decompensation increases GBW
product, ensuring that usable bandwidth is maintained
with increasing closed-loop gains. A GainAmp with a
fixed gain of A
120kHz. By comparison, a unity-gain-stable op amp con-
figured for A
of only 8kHz. Decompensation is performed at five inter-
mediate gain sets, as shown in the Gain Selector
Guide.
The MAX4074/MAX4075 family includes ±17V input
fault protection. For normal operation, see the input
voltage range specification in the Electrical Character-
istics. Overdriven inputs up to ±17V will not cause out-
put phase reversal. A back-to-back SCR structure at
the input pins allows either input to safely swing ±17V
relative to V
amp inputs are diode clamped to both supply rails for
Figure 2. Input Protection
EE
V
Fixed-Gain, GainAmp/Open-Loop Op Amps
= +25V/V would yield a -3dB bandwidth
(Figure 2). Additionally, the internal op
V
IN+
IN-
= +25V/V has a -3dB bandwidth of
______________________________________________________________________________________
Input Fault Protection
SCR
SCR
17V
V
17V
V
EE
EE
GainAmp Bandwidth
High-Voltage (±17V)
Micropower, SOT23, Rail-to-Rail,
R
G
5k
V
V
CC
EE
NOTE: INPUT STAGE PROTECTION INCLUDES TWO 17V SCRs
the protection of sensitive input stage circuitry. Current
through the clamp diodes is limited by a 5kΩ resistor at
the noninverting input, and by R
An IN+ or IN- fault voltage as high as ±17V causes less
than 3.5mA to flow through the input pin, protecting
both the GainAmp and the signal source from damage.
GainAmp fixed-gain amplifiers offer a precision, fixed-
gain amplifier in a small package that can be used in a
variety of circuit board designs. GainAmp fixed-gain
amplifiers can be used in many op amp circuits that
use resistive negative feedback to set gain, and do not
require other connections to the op amp inverting input.
Both inverting and noninverting op amp configurations
can be implemented easily using a GainAmp.
The MAX4074/MAX4075 combine both an op amp and
gain-setting feedback resistors on the same IC. The
inverting input voltage range is different from the nonin-
verting input voltage range because the inverting input
pin is connected to the R
with a discrete design, take care not to saturate the
inputs/output of the core op amp to avoid signal distor-
tions or clipping.
AND TWO DIODES AT THE INPUT STAGE.
R
F
Applications Information
GainAmp Input Voltage Range
MAX4074
MAX4075
G
input series resistor. Just as
G
at the inverting input.
OUT
11