HA3-2425-5 Intersil, HA3-2425-5 Datasheet - Page 4

• Manufacturer Part Number: HA3-2425-5
• Description: IC AMP SAMPLE&HOLD 3.2US 14-DIP
• Manufacturer: Intersil
• Type: Monolithicr

Specifications of HA3-2425-5

• Amplifier Type: Sample and Hold
• Number Of Circuits: 1
• Slew Rate: 5 V/µs
• Gain Bandwidth Product: 2.5MHz
• Current - Input Bias: 40nA
• Voltage - Input Offset: 3000µV
• Current - Supply: 3.5mA
• Current - Output / Channel: 15mA
• Voltage - Supply, Single/dual (±): ±12 V ~ 15 V
• Operating Temperature: 0°C ~ 75°C
• Mounting Type: Through Hole
• Package / Case: 14-DIP (0.300", 7.62mm)
• Bandwidth: 2.5 MHz
• Bandwidth, Gain: 2.5 MHz (Typ.)
• Common Mode Rejection Ratio: 90
• Current, Input Bias: 40 nA
• Current, Input Offset: 10 nA
• Current, Output: ±15 mA
• Current, Supply: 3.5 mA
• Impedance, Thermal: 95 °C/W
• Input Resistance: 10 Megohms (Typ.)
• Number Of Amplifiers: Single
• Package Type: PDIP-14
• Propagation Delay: 30 ns
• Resistance, Input: 10 Megohms
• Temperature, Operating, Maximum: +75 °C
• Temperature, Operating, Minimum: 0 °C
• Temperature, Operating, Range: 0 to +75 °C
• Time, Acquisition: 2.3 μs (Typ.)
• Time, Rise: 75 ns
• Time, Setting, Hold Mode: 860 ns (Typ.)
• Voltage, Gain: 50 kV/V
• Voltage, Input Offset: 3 mV
• Voltage, Offset, Input: 3 mV (Typ.)
• Voltage, Output Swing: ±10 V
• Voltage, Supply: ±15 V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

SEATING
Ceramic Dual-In-Line Frit Seal Packages (CERDIP)
NOTES:
10. Controlling dimension: INCH.
PLANE
PLANE
1. Index area: A notch or a pin one identification mark shall be locat-
2. The maximum limits of lead dimensions b and c or M shall be
3. Dimensions b1 and c1 apply to lead base metal only. Dimension
4. Corner leads (1, N, N/2, and N/2+1) may be configured with a
5. This dimension allows for off-center lid, meniscus, and glass
6. Dimension Q shall be measured from the seating plane to the
7. Measure dimension S1 at all four corners.
8. N is the maximum number of terminal positions.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
BASE
ccc
S1
b2
ed adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark.
measured at the centroid of the finished lead surfaces, when
solder dip or tin plate lead finish is applied.
M applies to lead plating and finish thickness.
partial lead paddle. For this configuration dimension b3 replaces
dimension b2.
overrun.
base plane.
M
C A - B
b
bbb
S
S
C A - B
D
A
-A-
-B-
A
D
e
S
S
12
D
-C-
S
-D-
E
Q
aaa
A
L
M
M
c1
e
A/2
C A - B
SECTION A-A
LEAD FINISH
METAL
BASE
(b)
b1
α
S
M
HA-2420, HA-2425
e
A
c
D
S
(c)
F14.3
14 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE
SYMBOL
eA/2
aaa
bbb
ccc
eA
S1
b1
b2
b3
c1
Q
M
A
D
E
α
N
b
c
e
L
MIL-STD-1835 GDIP1-T14 (D-1, CONFIGURATION A)
0.014
0.014
0.045
0.023
0.008
0.008
0.220
0.125
0.015
0.005
MIN
90
-
-
-
-
-
-
0.100 BSC
0.300 BSC
0.150 BSC
o
INCHES
14
0.200
0.026
0.023
0.065
0.045
0.018
0.015
0.785
0.310
0.200
0.060
0.015
0.030
0.010
0.0015
MAX
105
-
o
0.36
0.36
1.14
0.58
0.20
0.20
5.59
3.18
0.38
0.13
MIN
MILLIMETERS
90
-
-
-
-
-
-
o
2.54 BSC
7.62 BSC
3.81 BSC
14
19.94
5.08
0.66
0.58
1.65
1.14
0.46
0.38
7.87
5.08
1.52
0.38
0.76
0.25
0.038
MAX
105
-
o
Rev. 0 4/94
NOTES
FN2856.6
2, 3
2
3
4
2
3
5
5
6
7
8
-
-
-
-
-
-
-
-
-
-