ICL7611DCPA Intersil, ICL7611DCPA Datasheet - Page 6

• Manufacturer Part Number: ICL7611DCPA
• Description: IC OPAMP 1.4MHZ CMOS LP 8-DIP
• Manufacturer: Intersil

Specifications of ICL7611DCPA

• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Slew Rate: 1.6 V/µs
• Gain Bandwidth Product: 1.4MHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 15000µV
• Current - Supply: 1mA
• Current - Output / Channel: 40mA
• Voltage - Supply, Single/dual (±): 2 V ~ 16 V, ±1 V ~ 8 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Bandwidth: 1.4 MHz
• Channel Separation: 120
• Common Mode Rejection Ratio: 96
• Current, Input Bias: 400 pA
• Current, Input Offset: 300 pA
• Current, Output: 40 mA
• Current, Supply: 0.01 mA
• Number Of Amplifiers: Single
• Package Type: PDIP-8
• Resistance, Input: 10^12 Ohms
• Temperature, Operating, Range: 0 to +70 °C
• Time, Rise: 2 μs
• Voltage, Gain: 75 dB
• Voltage, Input: -4.7 to 5.3 V
• Voltage, Noise: 100 nV/sqrt Hz
• Voltage, Offset: 20 mV
• Voltage, Output, High: +4.8 V
• Voltage, Output, Low: -4.8 V
• Voltage, Supply: 18 V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Output Type: -
• -3db Bandwidth: -
• Other names: ICL7611DCPAIS

SEATING
Dual-In-Line Plastic Packages (PDIP)
INDEX
NOTES:
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3,
AREA
1. Controlling Dimensions: INCH. In case of conflict between
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Symbols are defined in the “MO Series Symbol List” in Section
4. Dimensions A, A1 and L are measured with the package seated
5. D, D1, and E1 dimensions do not include mold flash or protru-
6. E and
7. e
8. B1 maximum dimensions do not include dambar protrusions.
9. N is the maximum number of terminal positions.
PLANE
PLANE
BASE
English and Metric dimensions, the inch dimensions control.
2.2 of Publication No. 95.
in JEDEC seating plane gauge GS-3.
sions. Mold flash or protrusions shall not exceed 0.010 inch
(0.25mm).
pendicular to datum
strained. e
Dambar protrusions shall not exceed 0.010 inch (0.25mm).
E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch
(0.76 - 1.14mm).
D1
B1
B
and e
-A-
N
e
1 2 3
C
B
A
C
are measured at the lead tips with the leads uncon-
are measured with the leads constrained to be per-
must be zero or greater.
D
0.010 (0.25)
-C-
e
.
13
N/2
D1
M
-C-
E1
C A
-B-
A
1
A2
B S
L
e
A
C
ICL7611, ICL7612
e
e
C L
E
A
C
B
E8.3
8 LEAD DUAL-IN-LINE PLASTIC PACKAGE
SYMBOL
A1
A2
B1
D1
E1
e
e
C
D
N
A
B
E
e
L
A
B
(JEDEC MS-001-BA ISSUE D)
0.015
0.115
0.014
0.045
0.008
0.355
0.005
0.300
0.240
0.115
MIN
-
-
0.100 BSC
0.300 BSC
INCHES
8
MAX
0.210
0.195
0.022
0.070
0.014
0.400
0.325
0.280
0.430
0.150
-
-
MILLIMETERS
0.39
2.93
0.356
1.15
0.204
9.01
0.13
7.62
6.10
2.93
MIN
-
-
2.54 BSC
7.62 BSC
8
10.16
10.92
MAX
5.33
4.95
0.558
1.77
0.355
8.25
7.11
3.81
-
-
Rev. 0 12/93
NOTES
FN2919.9
8, 10
4
4
5
5
6
5
6
7
4
9
-
-
-
-