AD8512AR Analog Devices Inc, AD8512AR Datasheet - Page 17

• Manufacturer Part Number: AD8512AR
• Description: IC OPAMP JFET 8MHZ DUAL LN 8SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD8512AR

• Slew Rate: 20 V/µs
• Mounting Type: Surface Mount
• Rohs Status: RoHS non-compliant
• Design Resources: Precision, Bipolar Configuration for the AD5546/56 DAC (CN0024) Precision, Bipolar, Configuration for AD5547/AD5557 DAC (CN0028)
• Amplifier Type: J-FET
• Number Of Circuits: 2
• Gain Bandwidth Product: 8MHz
• Current - Input Bias: 25pA
• Voltage - Input Offset: 100µV
• Current - Supply: 2.2mA
• Current - Output / Channel: 70mA
• Voltage - Supply, Single/dual (±): ±4.5 V ~ 18 V
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 8-SOIC (3.9mm Width)
• No. Of Amplifiers: 2
• Bandwidth: 20MHz
• No. Of Pins: 8
• Operating Temperature Range: -40°C To +125°C
• Gain: 8dB
• Peak Reflow Compatible (260 C): No
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

I-V CONVERSION APPLICATIONS
Photodiode Circuits
Common applications for I-V conversion include photodiode
circuits where the amplifier is used to convert a current emitted
by a diode placed at the positive input terminal into an output
voltage.
The AD8510/AD8512/AD8513’s low input bias current, wide
bandwidth, and low noise make them each an excellent choice
for various photodiode applications, including fax machines,
fiber optic controls, motion sensors, and bar code readers.
The circuit shown in Figure 53 uses a silicon diode with zero
bias voltage. This is known as a photovoltaic mode; this
configuration limits the overall noise and is suitable for
instrumentation applications.
A larger signal bandwidth can be attained at the expense of
additional output noise. The total input capacitance (Ct)
consists of the sum of the diode capacitance (typically 3 pF to
4 pF) and the amplifier’s input capacitance (12 pF), which
includes external parasitic capacitance. Ct creates a pole in the
frequency response that can lead to an unstable system. To
ensure stability and optimize the bandwidth of the signal, a
capacitor is placed in the feedback loop of the circuit shown in
Figure 53. It creates a zero and yields a bandwidth whose corner
frequency is 1/(2π(R2Cf)).
The value of R2 can be determined by the ratio
where:
V is the desired output voltage of the op amp.
I
For example, if I
R2 should be 100 kΩ. Rd (see Figure 53) is a junction resistance
that drops typically by a factor of 2 for every 10°C increase in
temperature.
D
is the diode current.
V / I
D
Figure 53. Equivalent Preamplifier Photodiode Circuit
Rd
D
is 100 μA and a 10 V output voltage is desired,
Ct
2
3
AD8510
V
V
4
Cf
R2
EE
7
CC
6
Rev. I | Page 17 of 20
A typical value for Rd is 1000 MΩ. Because Rd >> R2, the
circuit behavior is not impacted by the effect of the junction
resistance. The maximum signal bandwidth is
where ft is the unity gain frequency of the amplifier.
Cf can be calculated by
where ft is the unity gain frequency of the op amp, and it achieves
a phase margin, φ
A higher phase margin can be obtained by increasing the value
of Cf. Setting Cf to twice the previous value yields approximately
φ
maximum signal bandwidth by 50%.
Using the previous parameters with a Cf ≈ 1 pF, the signal
bandwidth is approximately 2.6 MHz.
Signal Transmission Applications
One popular signal transmission method uses pulse-width
modulation. High data rates may require a fast comparator
rather than an op amp. However, the need for sharp, undistorted
signals may favor using a linear amplifier.
The AD8510/AD8512/AD8513 make excellent voltage
comparators. In addition to a high slew rate, the AD8510/
AD8512/AD8513 have a very fast saturation recovery time. In
the absence of feedback, the amplifiers are in open-loop mode
(very high gain). In this mode of operation, they spend much of
their time in saturation.
The circuit shown in Figure 54 was used to compare two signals
of different frequencies, namely a 100 Hz sine wave and a 1 kHz
triangular wave. Figure 55 shows a scope plot of the resulting
output waveforms. A pull-up resistor (typically 5 kΩ) can be
connected from the output to V
reach the positive rail. The trade-off is that power consumption
is higher.
M
= 65° and a maximal flat frequency response, but it reduces the
Cf
f
MAX
=
=
2π
Ct
2 π
R
2
R
M
Figure 54. Pulse-Width Modulator
ft
ft
2
, of approximately 45°.
Ct
V1
AD8510/AD8512/AD8513
3
2
V2
+15V
–15V
4
7
CC
6
if the output voltage needs to
V
OUT