AD8604ARZ Analog Devices Inc, AD8604ARZ Datasheet - Page 17
![IC OPAMP GP CMOS 8.4MHZ 14SOIC](/photos/5/67/56705/505-14-soic_sml.jpg)
AD8604ARZ
Manufacturer Part Number
AD8604ARZ
Description
IC OPAMP GP CMOS 8.4MHZ 14SOIC
Manufacturer
Analog Devices Inc
Series
DigiTrim®r
Specifications of AD8604ARZ
Slew Rate
6 V/µs
Amplifier Type
General Purpose
Number Of Circuits
4
Output Type
Rail-to-Rail
Gain Bandwidth Product
8.4MHz
Current - Input Bias
0.2pA
Voltage - Input Offset
80µV
Current - Supply
750µA
Current - Output / Channel
50mA
Voltage - Supply, Single/dual (±)
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
14-SOIC (3.9mm Width), 14-SOL
Op Amp Type
Precision
No. Of Amplifiers
4
Bandwidth
8.4MHz
Supply Voltage Range
2.7V To 5.5V
Amplifier Case Style
SOIC
No. Of Pins
14
Common Mode Rejection Ratio
89
Current, Input Bias
0.2 pA
Current, Input Offset
0.1 pA
Current, Output
±50 mA
Current, Supply
750 μA
Harmonic Distortion
0.004 %
Impedance, Thermal
36 °C/W
Number Of Amplifiers
Quad
Package Type
SOIC-14
Temperature, Operating, Range
-40 to +125 °C
Voltage, Gain
80 V/mV
Voltage, Input
5 V
Voltage, Noise
33 nV/sqrt Hz
Voltage, Offset
80 μV
Voltage, Output, High
4.975 V
Voltage, Output, Low
15 mV
Voltage, Supply
5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
-3db Bandwidth
-
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD8604ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD8604ARZ-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD8604ARZ-REEL7
Manufacturer:
FREESCALE
Quantity:
1 400
Part Number:
AD8604ARZ-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Voltage drop is created across the 0.1 Ω resistor that is
proportional to the load current. This voltage appears at the
inverting input of the amplifier due to the feedback correction
around the op amp. This creates a current through R1, which
in turn, pulls current through R2. For the low side monitor, the
monitor output voltage is given by
For the high side monitor, the monitor output voltage is
Using the components shown, the monitor output transfer
function is 2.5 V/A.
USING THE AD8601 IN SINGLE-SUPPLY, MIXED
SIGNAL APPLICATIONS
Single-supply, mixed signal applications requiring 10 or more
bits of resolution demand both a minimum of distortion and a
maximum range of voltage swing to optimize performance. To
ensure that the ADCs or DACs achieve their best performance, an
amplifier often must be used for buffering or signal conditioning.
The 750 μV maximum offset voltage of the AD8601 allows the
amplifier to be used in 12-bit applications powered from a 3 V
single supply, and its rail-to-rail input and output ensure no
signal clipping.
Figure 59 shows the AD8601 used as an input buffer amplifier
to the AD7476, a 12-bit, 1 MSPS ADC. As with most ADCs,
total harmonic distortion (THD) increases with higher source
impedances. By using the AD8601 in a buffer configuration, the
low output impedance of the amplifier minimizes THD while
the high input impedance and low bias current of the op amp
minimizes errors due to source impedance. The 8 MHz gain
bandwidth product of the AD8601 ensures no signal attenua-
tion up to 500 kHz, which is the maximum Nyquist frequency
for the AD7476.
Figure 59. A Complete 3 V 12-Bit 1 MHz Analog-to-Digital Conversion System
R
S
Monitor
Monitor
4
3
AD8601
5
2
Output
Output
1
680nF
GND
V
V
=
=
IN
DD
3
AD7476/AD7477
TANT
R2
V
1µF
×
−
⎛
⎜
⎝
⎡
⎢
⎣
R2
R
SENSE
R1
×
0.1µF
SDATA
REF193
⎛
⎜
⎝
SCLK
R
⎞
⎟
⎠
CS
SENSE
R1
×
10µF
I
INTERFACE
L
SERIAL
⎞
⎟
⎠
×
I
L
0.1µF
⎤
⎥
⎦
µC/µP
5V
SUPPLY
Rev. G | Page 17 of 24
(2)
(3)
Figure 60 demonstrates how the AD8601 can be used as an
output buffer for the DAC for driving heavy resistive loads. The
AD5320
up to 30 MHz and signal frequencies up to 930 kHz. The rail-
to-rail output of the AD8601 allows it to swing within 100 mV
of the positive supply rail while sourcing 1 mA of current. The
total current drawn from the circuit is less than 1 mA, or 3 mW
from a 3 V single supply.
The AD8601, AD7476, and AD5320 are all available in space-
saving SOT-23 packages.
PC100 COMPLIANCE FOR COMPUTER AUDIO
APPLICATIONS
Because of its low distortion and rail-to-rail input and output,
the AD860x is an excellent choice for low cost, single-supply
audio applications, ranging from microphone amplification
to line output buffering. Figure 38 shows the total harmonic
distortion plus noise (THD + N) figures for the AD860x. In
unity gain, the amplifier has a typical THD + N of 0.004%, or
−86 dB, even with a load resistance of 600 Ω. This is compliant
with the PC100 specification requirements for audio in both
portable and desktop computers.
Figure 61 shows how an AD8602 can be interfaced with an AC’97
codec to drive the line output. Here, the AD8602 is used as a
unity-gain buffer from the left and right outputs of the AC’97
codec. The 100 μF output coupling capacitors block dc current
and the 20 Ω series resistors protect the amplifier from short
circuits at the jack.
Figure 60. Using the AD8601 as a DAC Output Buffer to Drive Heavy Loads
INTERFACE
SERIAL
3-WIRE
RIGHT
is a 12-bit DAC that can be used with clock frequencies
AD1881
(AC’97)
LEFT
Figure 61. A PC100-Compliant Line Output Amplifier
V
V
OUT
OUT
V
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
DD
DD
SS
1µF
4
5
6
25
29
35
36
26
AD5320
5V
3V
AD8601/AD8602/AD8604
2
3
5
6
AD8602
AD8602
1
A
B
5V
8
4
1
7
4
3
100µF
100µF
C1
C2
2kΩ
2kΩ
2
R2
R3
5
AD8601
1
20Ω
20Ω
R4
R5
V
0V TO 3V
OUT
R
L