OP97FS Analog Devices Inc, OP97FS Datasheet - Page 13

• Manufacturer Part Number: OP97FS
• Description: IC OPAMP GP LP PREC 8SOIC
• Manufacturer: Analog Devices Inc

Specifications of OP97FS

• Slew Rate: 0.2 V/µs
• Rohs Status: RoHS non-compliant
• Amplifier Type: General Purpose
• Number Of Circuits: 1
• -3db Bandwidth: 900kHz
• Current - Input Bias: 30pA
• Voltage - Input Offset: 30µV
• Current - Supply: 380µA
• Voltage - Supply, Single/dual (±): ±2 V ~ 20 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• No. Of Amplifiers: 1
• Bandwidth: 900kHz
• No. Of Pins: 8
• Operating Temperature Range: -40°C To +85°C
• Peak Reflow Compatible (260 C): No
• Input Bias Current: 0.15nA
• Output Type: -
• Current - Output / Channel: -
• Gain Bandwidth Product: -
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

GUARDING AND SHIELDING
To maintain the extremely high input impedances of the OP97,
care must be taken in circuit board layout and manufacturing.
Board surfaces must be kept scrupulously clean and free of
moisture. Conformal coating is recommended to provide a
humidity barrier. Even a clean PCB can have 100 pA of leakage
currents between adjacent traces; therefore, use guard rings
around the inputs. Guard traces are operated at a voltage close
to that on the inputs, so that leakage currents are minimal. In
noninverting applications, connect the guard ring to the common-
mode voltage at the inverting input (Pin 2). In inverting appli-
cations, both inputs remain at ground, so that the guard trace
should be grounded. Make guard traces on both sides of the
circuit board.
High impedance circuitry is extremely susceptible to RF pickup,
line frequency hum, and radiated noise from switching power
supplies. Enclosing sensitive analog sections within grounded
shields is generally necessary to prevent excessive noise pickup.
Twisted-pair cable aid in rejection of line frequency hum.
DIGITAL
R
INPUTS
AD7548
FB
Figure 35. DAC Output Amplifier
30pF
I
I
O
O
2
3
OP97
6
UNITY-GAIN FOLLOWE
INVERTING AMPLIFIER
2
3
2
3
V
OP97
OP97
OUT
Figure 37. Guard Ring Layout and Connections
6
6
R
Rev. G | Page 13 of 16
The OP97 is an excellent choice as an output amplifier for
higher resolution CMOS DACs. Its tightly trimmed offset
voltage and minimal bias current result in virtually no
degradation of linearity, even over wide temperature ranges.
Figure 36 shows a versatile monitor circuit that can typically
sense current at any point between the ±15 V supplies. This
makes it ideal for sensing current in applications such as full
bridge drivers where bidirectional current is associated with
large common-mode voltage changes. The 114 dB CMRR of the
OP97 makes the contribution of the amplifier to common-
mode error negligible, leaving only the error due to the resistor
ratio inequality. Ideally, R2/R4 = R3/R5.
NONINVERTING AMPLIFIER
8
BOTTOM VIEW
2
3
V1
OP97
PDIP
10kΩ
R2
10kΩ
10kΩ
R1
6
R3
1
Figure 36. Current Monitor
10kΩ
R4
2
3
OP97
10kΩ
R5
+15V
–15V
7
4
6
I
L
R
L
V
OUT
OP97