MCP609-I/ST Microchip Technology, MCP609-I/ST Datasheet - Page 13

• Manufacturer Part Number: MCP609-I/ST
• Description: IC OPAMP 2.5V QUAD R-R 14TSSOP
• Manufacturer: Microchip Technology

Specifications of MCP609-I/ST

• Slew Rate: 0.08 V/µs
• Amplifier Type: General Purpose
• Number Of Circuits: 4
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 155kHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 250µV
• Current - Supply: 18.7µA
• Current - Output / Channel: 17mA
• Voltage - Supply, Single/dual (±): 2.5 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Op Amp Type: Low Power
• No. Of Amplifiers: 4
• Bandwidth: 155kHz
• Supply Voltage Range: 2.5V To 5.5V
• Amplifier Case Style: TSSOP
• No. Of Pins: 14
• Number Of Channels: 4
• Voltage Gain Db: 121 dB
• Common Mode Rejection Ratio (min): 75 dB
• Input Offset Voltage: 0.25 mV
• Operating Supply Voltage: 3 V, 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Details

3.0
Descriptions of the pins are listed in
TABLE 3-1:
3.1
The output pins are low-impedance voltage sources.
3.2
The non-inverting and inverting inputs are high-
impedance CMOS inputs with low bias currents.
3.3
The Chip Select (CS) pin is a Schmitt-triggered, CMOS
logic input. It is used to place the MCP608 op amp in a
Low-power mode, with the output(s) in a Hi-Z state.
© 2009 Microchip Technology Inc.
PDIP, SOIC,
TSSOP
1, 5, 8
—
—
—
—
—
—
—
—
—
—
6
2
3
7
4
PIN DESCRIPTIONS
Analog Outputs
Analog Inputs
Chip Select Digital Input
MCP606
PIN FUNCTION TABLE
SOT-23-5
—
—
—
—
—
—
—
—
—
—
—
1
4
3
5
2
MCP607
—
—
—
—
—
—
—
—
1
2
3
8
5
6
7
4
Table
3-1.
MCP608
1, 5
—
—
—
—
—
—
—
—
—
6
2
3
7
4
8
MCP609
10
12
13
14
11
—
—
1
2
3
4
5
6
7
8
9
3.4
The positive power supply pin (V
higher than the negative power supply pin (V
normal operation, the output pins are at voltages
between V
voltages between V
Typically, these parts are used in a single-supply
(positive) configuration. In this case, V
to ground and V
need bypass capacitors .
V
V
V
OUT
IN
IN
Symbol
V
V
V
V
V
V
V
V
V
–, V
+, V
V
V
OUTB
OUTC
OUTD
CS
NC
INB
INB
INC
INC
IND
IND
, V
Power Supply Pins
DD
SS
SS
OUTA
INA
INA
+
–
+
+
–
–
–
+
and V
DD
Output (op amp A)
Inverting Input (op amp A)
Non-inverting Input (op amp A)
Positive Power Supply
Non-inverting Input (op amp B)
Inverting Input (op amp B)
Output (op amp B)
Output (op amp B)
Inverting Input (op amp C)
Non-inverting Input (op amp C)
Negative Power Supply
Non-inverting Input (op amp D)
Inverting Input (op amp D)
Output (op amp D)
Chip Select
No Internal Connection
MCP606/7/8/9
is connected to the supply. V
SS
DD
– 0.3V and V
; while the input pins are at
Description
DD
DD
DS11177F-page 13
) is 2.5V to 5.5V
SS
+ 0.3V.
is connected
SS
DD
). For
will