MAX9945AUA+ Maxim Integrated Products, MAX9945AUA+ Datasheet - Page 7
![IC OPAMP MOS-INPUT LP/LN 8-MSOP](/photos/1/39/13936/406-8-msop_sml.jpg)
MAX9945AUA+
Manufacturer Part Number
MAX9945AUA+
Description
IC OPAMP MOS-INPUT LP/LN 8-MSOP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX9945EVKIT.pdf
(14 pages)
Specifications of MAX9945AUA+
Amplifier Type
General Purpose
Number Of Circuits
1
Output Type
Rail-to-Rail
Slew Rate
2.2 V/µs
Gain Bandwidth Product
3MHz
Current - Input Bias
0.05pA
Voltage - Input Offset
600µV
Current - Supply
400µA
Current - Output / Channel
25mA
Voltage - Supply, Single/dual (±)
4.75 V ~ 38 V, ±2.4 V ~ 19 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Input Offset Voltage
+/- 0.6 V
Input Bias Current (max)
50 fA
Common Mode Rejection Ratio (min)
94 dB
Supply Current
850 uA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Input Voltage
- 0.3 V to + 40 V
Maximum Power Dissipation
387.8 mW
Mounting Style
SMD/SMT
Operating Temperature Range
- 40 C to + 125 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
-3db Bandwidth
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
The MAX9945 features a combination of low input cur-
rent and voltage noise, rail-to-rail output voltage swing,
wide supply voltage range, and low-power operation.
The MOS inputs on the MAX9945 make it ideal for use
as transimpedance amplifiers and high-impedance
sensor interface front-ends in medical and industrial
applications. The MAX9945 can interface with small
signals from either current-sources or high-output
impedance voltage sources. Applications include pho-
todiode pulse oximeters, pH sensors, capacitive pres-
sure sensors, chemical analysis equipment, smoke
detectors, and humidity sensors.
A high 130dB open-loop gain (typ) and a wide supply
voltage range, allow high signal-gain implementations
prior to signal conditioning circuitry. Low quiescent
supply current makes the MAX9945 compatible with
portable systems and applications that operate under
tight power budgets. The combination of excellent THD,
low voltage noise, and MOS inputs also make the
MAX9945 ideal for use in high-performance active fil-
ters for data acquisition systems and audio equipment.
The MAX9945 features a MOS-input stage with only
50fA (typ) of input bias current and a low 1fA/√Hz (typ)
input current-noise density. The low-frequency input
voltage noise is a low 2µV
accepts a wide common-mode range, extending from
the negative supply, V
supply, V
TDFN-EP
—
1
2
3
4
5
6
Low-Current, Low-Noise Input Stage
CC
.
PIN
_______________________________________________________________________________________
µMAX
1, 5, 8
—
6
4
3
2
7
Detailed Description
EE,
to within 1.2V of the positive
P-P
NAME
OUT
N.C.
V
V
IN+
IN-
EP
CC
EE
(typ). The input stage
Amplifier Output
Negative Power Supply. Bypass V
capacitors to quiet ground plane if different from V
Noninverting Amplifier Input
Inverting Amplifier Input
No Connection. Not internally connected.
Positive Power Supply. Bypass V
to quiet ground plane or V
Exposed Pad (TDFN Only). Connect to V
to maximize thermal performance. Not intended as an electrical connection (TDFN only).
38V, Low-Noise, MOS-Input,
The MAX9945 output stage swings to within 50mV (typ)
of either power-supply rail with a 100kΩ load and pro-
vides a 3MHz GBW with a 2.2V/µs slew rate. The
device is unity-gain stable, and unlike other devices
with a low quiescent current, can drive a 120pF capaci-
tive load without compromising stability.
High-impedance sensors can output signals of interest
in either current or voltage form. The MAX9945 inter-
faces to both current-output sensors such as photo-
diodes and potentiostat sensors, and high-impedance
voltage sources such as pH sensors.
For current-output sensors, a transimpedance amplifier
is the most noise-efficient method for converting the
input signal to a voltage. High-value feedback resistors
are commonly chosen to create large gains, while feed-
back capacitors help stabilize the amplifier by cancel-
ing any zeros in the transfer function created by a
highly capacitive sensor or cabling. A combination of
low-current noise and low-voltage noise is important for
these applications. Take care to calibrate out photodi-
ode dark current if DC accuracy is important. The high
bandwidth and slew rate also allows AC signal pro-
cessing in certain medical photodiode sensor applica-
tions such as pulse oximetry.
EE
.
CC
EE
Low-Power Op Amp
with 0.1µF ceramic and 4.7µF electrolytic capacitors
with 0.1µF ceramic and 4.7µF electrolytic
High-Impedance Sensor Front Ends
FUNCTION
EE
externally. Connect to a large copper plane
Applications Information
EE.
Rail-to-Rail Output Stage
Pin Description
7