MCP6271-E/P Microchip Technology, MCP6271-E/P Datasheet - Page 2

• Manufacturer Part Number: MCP6271-E/P
• Description: IC OPAMP 2.0V SNGL R-R 8DIP
• Manufacturer: Microchip Technology

Specifications of MCP6271-E/P

• Slew Rate: 0.9 V/µs
• Package / Case: 8-DIP (0.300", 7.62mm)
• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 2MHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 3000µV
• Current - Supply: 170µA
• Current - Output / Channel: 25mA
• Voltage - Supply, Single/dual (±): 2 V ~ 6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Through Hole
• Number Of Channels: 1
• Common Mode Rejection Ratio (min): 70 dB
• Input Offset Voltage: 3 mV
• Input Bias Current (max): 1 pA
• Operating Supply Voltage: 3 V, 5 V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Shutdown: No
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Technology: CMOS
• Voltage Gain Db: 110 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP6XXXDM-FLTR - KIT DEMO BOARD ACTIVE FILTER
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MCP6271/1R/2/3/4/5
1.0
Absolute Maximum Ratings †
V
Current at Input Pins ....................................................±2 mA
Analog Inputs (V
All other Inputs and Outputs .......... V
Difference Input Voltage ...................................... |V
Output Short Circuit Current .................................Continuous
Current at Output and Supply Pins ............................±30 mA
Storage Temperature....................................–65°C to +150°C
Junction Temperature (T
ESD Protection On All Pins (HBM/MM) ................ ≥ 4 kV/400V
DC ELECTRICAL SPECIFICATIONS
DS21810F-page 2
Electrical Characteristics: Unless otherwise indicated, T
V
Input Offset (Note 1)
Input Offset Voltage
Input Offset Voltage
Input Offset Temperature Drift
Power Supply Rejection Ratio
Input Bias Current and Impedance
Input Bias Current
Input Offset Current
Common Mode Input Impedance
Differential Input Impedance
Common Mode (Note 4)
Common Mode Input Voltage Range
Common Mode Rejection Ratio
Common Mode Rejection Ratio
Open-Loop Gain
DC Open-Loop Gain (Large Signal)
Note 1:
DD
OUT
(Extended Temperature)
– V
At Temperature
At Temperature
≈ V
2:
3:
4:
5:
6:
7:
SS
ELECTRICAL
CHARACTERISTICS
DD
........................................................................7.0V
/2, V
Parameters
The MCP6275’s V
The current at the MCP6275’s V
This specification does not apply to the MCP6275’s V
The MCP6275’s V
V
has a voltage range specified by V
Set by design and characterization.
Does not apply to op amp B of the MCP6275.
All parts with date codes November 2007 and later have been screened to ensure operation at V
the other minimum and maximum specifications are measured at 2.0V and 5.5V.
DD
IN
L
– 100 mV. CMRR is not measured for op amp B of the MCP6275. The MCP6275’s V
+ and V
= V
DD
J
/2, R
) . .........................................+150°C
IN
–) †† .. V
L
CM
= 10 kΩ to V
INB
– pin (op amp B) has a common mode input voltage range (V
for op amp B (pins V
SS
SS
ΔV
– 1.0V to V
– 0.3V to V
CMRR
CMRR
PSRR
V
V
Z
Sym
V
V
OS
Z
A
I
DIFF
CMR
CMR
I
I
I
OS
CM
OS
OS
OL
L
B
B
B
/ΔT
INB
and CS is tied low. (Refer to
OH
A
– pin is specified by I
DD
DD
V
V
and V
DD
SS
SS
+ 1.0V
+ 0.3V
–3.0
–5.0
– V
Min
70
70
65
90
OUTA
—
—
—
—
—
—
—
− 0.15
− 0.30
OL
SS
A
.
= +25°C, V
/V
|
INB
+ and V
10
10
OUTA
±1.7
±1.0
±1.0
Typ
110
90
50
85
80
—
—
13
13
—
—
2
B
||6
||3
only.
† Notice: Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of
the device at those or any other conditions above those
indicated in the operational listings of this specification is not
implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
†† See Section 4.1.2 “Input Voltage and Current Limits”.
/V
DD
INB
INB
Figure 1-2
= +2.0V to +5.5V, V
–) is V
V
V
+ pin.
DD
DD
+3.0
+5.0
Max
200
—
—
—
—
—
—
—
—
—
+ 0.15
+ 0.30
5
SS
and
+ 100 mV.
µV/°C T
Figure
Units
Ω||pF Note 3
Ω||pF Note 3
mV
mV
dB
pA
pA
nA
pA
dB
dB
dB
V
V
SS
CMR
1-3).
= GND, V
V
T
V
Note 2
T
T
Note 3
V
V
V
(Note 6)
V
(Note 6)
V
V
© 2008 Microchip Technology Inc.
A
A
A
A
CM
CM
DD
DD
CM
CM
OUT
CM
= +85°C (Note 2)
= +125°C (Note 2)
= –40°C to +125°C, V
= –40°C to +125°C, V
) of V
= 2.0V (Note 5)
= 5.5V (Note 5)
= –0.3V to 2.5V, V
= –0.3V to 5.3V, V
= V
= V
= V
OUTA
= 0.2V to V
SS
SS
SS
SS
CM
/V
Conditions
(Note 1)
+ 100 mV to
DD
INB
= V
= 6.0V. However,
+ pin (op amp B)
DD
DD
/2,
– 0.2V,
DD
DD
CM
CM
= 5V
= 5V
= V
= V
SS
SS