PA241DF Cirrus Logic Inc, PA241DF Datasheet - Page 5
![OP AMP HV 350V .06A 24-PSOP DF](/photos/12/49/124975/pa241df_sml.jpg)
PA241DF
Manufacturer Part Number
PA241DF
Description
OP AMP HV 350V .06A 24-PSOP DF
Manufacturer
Cirrus Logic Inc
Series
Apex Precision Power™r
Specifications of PA241DF
Amplifier Type
Power
Number Of Circuits
1
Slew Rate
30 V/µs
Gain Bandwidth Product
3MHz
Current - Input Bias
50pA
Voltage - Input Offset
25000µV
Current - Supply
2.2mA
Current - Output / Channel
120mA
Voltage - Supply, Single/dual (±)
100 V ~ 350 V, ±50 V ~ 175 V
Operating Temperature
-25°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-PSOP
Number Of Channels
1
Voltage Gain Db
96 dB
Common Mode Rejection Ratio (min)
84 dB
Input Offset Voltage
40 mV
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Maximum Dual Supply Voltage
+/- 175 V
Minimum Operating Temperature
- 25 C
For Use With
598-1459 - EVALUATION KIT FRO PA241DF
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
-3db Bandwidth
-
Lead Free Status / Rohs Status
Details
Other names
598-1357
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PA241DF
Manufacturer:
APEX
Quantity:
20 000
GENERAL
erations" which covers stability, power supplies, heat sinking,
mounting, current limit, SOA interpretation, and specification
interpretation. Visit www.Cirrus.com for design tools that help
automate tasks such as calculations for stability, internal power
dissipation, current limit, heat sink selection, Apex Precision
Power's complete Application Notes library, Technical Seminar
Workbook and Evaluation Kits.
PHASE COMPENSATION
ing temperature. The PHASE COMPENSATION typical graph
shows closed loop gain and phase compensation capacitor
value relationships for four case temperatures. The curves are
based on achieving a phase margin of 50°. Calculate the high-
est case temperature for the application (maximum ambient
temperature and highest internal power dissipation) before
choosing the compensation. Keep in mind that when working
with small values of compensation, parasitics may play a large
role in performance of the finished circuit. The compensation
capacitor must be rated for at least the total voltage applied
to the amplifier and should be a temperature stable type such
as NPO or COG.
OTHER STABILITY CONCERNS
when choosing compensation. They stem from the fact that
while "gain" is the most commonly used term, β (the feedback
factor) is really what counts when designing for stability.
1. Gain must be calculated as a non-inverting circuit (equal
2. Including a feedback capacitor changes the feedback factor
(parallel combination of the feedback resistor and all input
resistors) should be limited to 5k ohms or less. The amplifier
input capacitance of about 6pF, plus capacitance of connecting
traces or wires and (if used) a socket will cause undesirable
circuit performance and even oscillation if these resistances
are too high. In circuits requiring high resistances, measure or
estimate the total sum point capacitance, multiply by Rin/Rf, and
parallel Rf with this value. Capacitors included for this purpose
are usually in the single digit pF range. This technique results
in equal feedback factor calculations for AC and DC cases. It
does not produce a roll off, but merely keeps β constant over
a wide frequency range. Paragraph 6 of Application Note 19
details suitable stability tests for the finished circuit.
PA241U
Please read Application Note 1 "General Operating Consid-
Open loop gain and phase shift both increase with increas-
There are two important concepts about closed loop gain
As a general rule the DC summing junction impedance
input and feedback resistors can provide a signal gain of
-1, but for calculating offset errors, noise, and stability, this
is a gain of 2).
or gain of the circuit. Consider Rin=4.7k, Rf=47k for a gain
of 11. Compensation of 4.7 to 6.8pF would be reasonable.
Adding 33pF parallel to the 47k rolls off the circuit at 103kHz,
and at 2MHz has reduced gain from 11 to roughly 1.5 and
the circuit is likely to oscillate.
P r o d u c t I n n o v a t i o n F r o m
CURRENT LIMIT
connected as shown in the external connection diagram. The
minimum value is 3.9 ohms, however for optimum reliability,
the resistor should be set as high as possible. The maximum
practical value is 110 ohms. Current limit values can be pre-
dicted as follows:
graph.
the +Vs pin, -Vbe for current through the -Vs pin, and that they
vary with case temperature. Value of the current limit resistor
at a case temperature of 25° can be estimated as follows:
oscillation present during the current limited portion of the nega-
tive half cycle. The frequency of the oscillation is not predictable
and depends on the compensation, gain of the amplifier, value
of the current limit resistor, and the load. The oscillation will
cease as the amplifier comes out of current limit.
SAFE OPERATING AREA
second breakdown considerations as in bipolar output stages.
However there are still three distinct limitations:
1. Voltage withstand capability of the transistors.
2. Current handling capability of the die metalization.
3. Temperature of the output MOSFETS.
ing Area graphs). Note that each pulse capability line shows
a constant power level (unlike second breakdown limitations
where power varies with voltage stress). These lines are shown
for a case temperature of 25°C and correspond to thermal
resistances of 5.2°C/W for the PA241CE and DF and 10.4°C/W
for the PA241DW respectively. Pulse stress levels for other
case temperatures can be calculated in the same manner as
DC power levels at different temperatures. The output stage
is protected against transient flyback by the parasitic diodes of
the output stage MOSFET structure. However, for protection
against sustained high energy flyback external fast-recovery
diodes must be used.
HEATSINKING
copper heatslug to which the monolithic amplifier is directly
attached. The solder connection of the heatslug to a minimum
of 1 square inch foil area on the printed circuit board will result
in thermal performance of 25°C/W junction to air rating of the
PA241DF. Solder connection to an area of 1 to 2 square inches
is recommended. This may be adequate heatsinking but the
large number of variables involved suggest temperature mea-
surements be made on the top of the package. Do not allow
the temperature to exceed 85°C.
For proper operation, the current limit resistor, Rcl, must be
Note that +Vbe should be used to predict current through
When the amplifier is current limiting, there may be spurious
The MOSFET output stage of the PA241 is not limited by
These limitations can be seen in the SOA (see Safe Operat-
The PA241DF package has a large exposed integrated
Where Vbe is shown in the CURRENT LIMIT typical
Ilimit = Vbe
Rcl = 0.7
Ilimit
Rcl
PA241
5