AD524ADZ Analog Devices Inc, AD524ADZ Datasheet - Page 17
![IC AMP INST 1MHZ PREC LN 16CDIP](/photos/6/64/66415/505-16-cdip_heat_pad_sml.jpg)
AD524ADZ
Manufacturer Part Number
AD524ADZ
Description
IC AMP INST 1MHZ PREC LN 16CDIP
Manufacturer
Analog Devices Inc
Type
Precisionr
Specifications of AD524ADZ
Amplifier Type
Instrumentation
Number Of Circuits
1
Slew Rate
5 V/µs
Gain Bandwidth Product
1MHz
-3db Bandwidth
1MHz
Current - Input Bias
50nA
Voltage - Input Offset
250µV
Current - Supply
3.5mA
Voltage - Supply, Single/dual (±)
±6 V ~ 18 V
Operating Temperature
-25°C ~ 85°C
Mounting Type
Through Hole
Package / Case
16-CDIP (0.300", 7.62mm)
Bandwidth
25 MHz
Common Mode Rejection Ratio
110
Current, Input Bias
±50 nA
Current, Input Offset
±35 nA
Current, Supply
3.5 mA (Quiescent)
Package Type
SBDIP-16
Power Dissipation
450 mW
Resistance, Input
20 Kilohms
Temperature, Operating, Range
-25 to +85 °C
Voltage, Gain
1-1000 V/V
Voltage, Input
<36 V
Voltage, Input Offset
250 μV
Voltage, Noise
7 nV/sqrt Hz (Input), 90 nV/sqrt Hz (Output)
Voltage, Supply
±15 V
No. Of Amplifiers
5
Input Offset Voltage
250µV
Gain Db Min
1dB
Amplifier Output
Single Ended
Cmrr
110dB
Supply Voltage Range
± 6V To ± 18V
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
Current - Output / Channel
-
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD524ADZ
Manufacturer:
AD
Quantity:
1 000
Company:
Part Number:
AD524ADZ
Manufacturer:
AD
Quantity:
1 000
Part Number:
AD524ADZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
The AD524 can also be configured to provide gain in the output
stage. Figure 37 shows an H pad attenuator connected
to the reference and sense lines of the AD524. R1, R2, and R3
should be made as low as possible to minimize the gain variation
and reduction of CMRR. Varying R2 precisely sets the gain
without affecting CMRR. CMRR is determined by the match
of R1 and R3.
Table 4. Output Gain Resistor Values
INPUT BIAS CURRENTS
Input bias currents are those currents necessary to bias the
input transistors of a dc amplifier. Bias currents are an
additional source of input error and must be considered in
a total error budget. The bias currents, when multiplied by
the source resistance, appear as an offset voltage. What is of
concern in calculating bias current errors is the change in bias
current with respect to signal voltage and temperature. Input
offset current is the difference between the two input bias
currents. The effect of offset current is an input offset voltage
whose magnitude is the offset current times the source
impedance imbalance.
Figure 38. Indirect Ground Returns for Bias Currents—Transformer Coupled
Output Gain
2
5
10
–INPUT
+INPUT
G =
Figure 39. Indirect Ground Returns for Bias Currents—Thermocouple
(R2||40kΩ) + R1 + R3
(R2||40kΩ)
G = 1000
G = 100
G = 10
RG
RG
2
1
R2
5 kΩ
1.05 kΩ
1 kΩ
Figure 37. Gain of 2000
16
13
12
11
1
3
2
12
13
16
11
2
3
1
11
12
13
16
2
3
1
+
–
+
–
AD524
AD524
AD524
–V
+V
–V
+V
–V
8
7
+V
8
7
S
S
S
8
7
S
S
S
R1, R3
2.26 kΩ
2.05 kΩ
4.42 kΩ
10
10
6
6
10
9
6
9
(R1 + R2 + R3)||R
LOAD
LOAD
9
Nominal Gain
2.02
5.01
10.1
R2
5kΩ
R3
2.26kΩ
TO POWER
SUPPLY
GROUND
TO POWER
SUPPLY
GROUND
2.26kΩ
R1
L
≥ 2kΩ
R
L
V
OUT
Rev. F | Page 17 of 28
Although instrumentation amplifiers have differential inputs,
there must be a return path for the bias currents. If this is not
provided, those currents charge stray capacitances, causing the
output to drift uncontrollably or to saturate. Therefore, when
amplifying floating input sources such as transformers and
thermocouples, as well as ac-coupled sources, there must still
be a dc path from each input to ground.
COMMON-MODE REJECTION
Common-mode rejection is a measure of the change in output
voltage when both inputs are changed equal amounts. These
specifications are usually given for a full-range input voltage
change and a specified source imbalance. Common-mode
rejection ratio (CMRR) is a ratio expression whereas common-
mode rejection (CMR) is the logarithm of that ratio. For
example, a CMRR of 10,000 corresponds to a CMR of 80 dB.
In an instrumentation amplifier, ac common-mode rejection is
only as good as the differential phase shift. Degradation of ac
common-mode rejection is caused by unequal drops across
differing track resistances and a differential phase shift due
to varied stray capacitances or cable capacitances. In many
applications, shielded cables are used to minimize noise. This
technique can create common-mode rejection errors unless the
shield is properly driven. Figure 41 and Figure 42 show active
data guards that are configured to improve ac common-mode
rejection by bootstrapping the capacitances of the input cabling,
thus minimizing differential phase shift.
Figure 40. Indirect Ground Returns for Bias Currents–AC-Coupled
100Ω
100Ω
100Ω
AD711
Figure 42. Differential Shield Driver
Figure 41. Shield Driver, G ≥ 100
AD712
–INPUT
G = 100
+INPUT
12
11
13
16
2
3
1
–V
RG
–INPUT
+INPUT
S
+
–
AD524
2
RG
RG
12
1
3
2
+V
–V
1
8
7
2
–
+
12
S
16
S
1
3
2
AD524
–
+
+V
–V
AD524
8
7
10
6
S
S
–V
+V
8
7
S
9
S
LOAD
10
6
10
6
9
9
TO POWER
SUPPLY
GROUND
REFERENCE
V
OUT
AD524
V
REFERENCE
OUT