AD8036ARZ Analog Devices Inc, AD8036ARZ Datasheet
AD8036ARZ
Specifications of AD8036ARZ
Available stocks
Related parts for AD8036ARZ
AD8036ARZ Summary of contents
Page 1
PRODUCT DESCRIPTION The AD8036 and AD8037 are wide bandwidth, low distortion clamping amplifiers. The AD8036 is unity gain stable. The AD8037 is stable at a gain of two or greater. These devices allow the designer to specify a ...
Page 2
AD8036/AD8037–SPECIFICATIONS ELECTRICAL CHARACTERISTICS Parameter Conditions DYNAMIC PERFORMANCE Bandwidth (–3 dB) Small Signal V 1 Large Signal 8036, V Bandwidth for 0.1 dB Flatness V 8036, R Slew Rate, Average +/– V Rise/Fall Time V V Settling Time To 0.1% V ...
Page 3
ABSOLUTE MAXIMUM RATINGS Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V ...
Page 4
AD8036/AD8037 AD8036–Typical Characteristics PULSE 0.1 F GENERATOR 350ps R F AD8036 130 –V S Ω Ω PULSE 0.1 F GENERATOR 350ps ...
Page 5
AD8037–Typical Characteristics R F PULSE 10 F GENERATOR + 350ps AD8037 100 –V S Ω PULSE GENERATOR 350ps 0.1 F ...
Page 6
AD8036/AD8037 AD8036–Typical Characteristics 300mV p-p – 102 S – 100 L 49.9 –3 –4 –5 –6 –7 –8 1M 10M 100M FREQUENCY – Hz 0.2 0.1 0 –0.1 140 ...
Page 7
p-p O – 500 –70 2ND HARMONIC –90 3RD HARMONIC –110 –130 10k 100k 1M 10M FREQUENCY – Hz Ω – p-p O ...
Page 8
AD8036/AD8037 AD8037–Typical Characteristics 300mV p-p 274 174 R = 100 –1 –2 1M 10M 100M FREQUENCY – Hz 0.2 0 ...
Page 9
p – 500 –70 2ND HARMONIC –90 3RD HARMONIC –110 –130 10k 100k 1M 10M FREQUENCY – Hz Ω – p-p O ...
Page 10
AD8036/AD8037–Typical Characteristics 100 1k FREQUENCY – –PSRR 70 65 +PSRR 10k 100k 1M 10M FREQUENCY ...
Page 11
V 100 0.1 0.01 1.0M 10M 0.1M FREQUENCY – 100 0.1 0.01 1.0M 10M 0.1M FREQUENCY – Hz 4.2 4.1 +V OUT 4.0 –V OUT 3.9 ...
Page 12
AD8036/AD8037–Typical Characteristics AD8037 AD8037 –60 –40 – JUNCTION TEMPERATURE – C –2. –2.25 –2.00 AD8037 –1. –1.50 –1.25 AD8036 ...
Page 13
AD8036 AD8037 –3V –2V – AD8036 –5 AD8037 – +1V +2V –15 –20 –3 –2 – ...
Page 14
AD8036/AD8037–Clamp Characteristics 0.5 0.4 0.3 0.2 0.1 0 –0.1 –0.2 –0.3 –0.4 –0 SETTLING TIME – ns × 0.5 0.4 0.3 0.2 0.1 0 –0.1 –0.2 –0.3 –0.4 –0 ...
Page 15
THEORY OF OPERATION General The AD8036 and AD8037 are wide bandwidth, voltage feedback clamp amplifiers. Since their open-loop frequency response fol- lows the conventional 6 dB/octave roll-off, their gain bandwidth product is basically constant. Increasing their closed-loop gain results in ...
Page 16
AD8036/AD8037 – INPUT CLAMPING AMPLIFIER OPERATION The key to the AD8036 and AD8037’s fast, accurate clamp and amplifier performance is their unique patent pending CLAMPIN input clamp architecture. This ...
Page 17
For instance, to set an output limit of ± for an AD8037 operating at a gain of 3. would need to be set to +0.333 V and –0.333 V, respectively. L ...
Page 18
AD8036/AD8037 +5V V 0.1 F 10µF 2.5V AD780 0.1 F Clamping with an Offset Some op amp circuits are required to operate with an offset voltage. These are generally configured in the inverting mode where the offset voltage can be ...
Page 19
TTL IN 1.3k –15V 274 The circuit uses an AD8037 operating at a gain of two with an AD811 to boost the output to the ± range. The AD811 was chosen for its ability to operate ...
Page 20
AD8036/AD8037 Thus for either positive or negative input signals, the output is unity times the absolute value of the input signal. The circuit can be easily configured to produce the negative absolute value of the input by applying the input ...
Page 21
Layout Considerations The specified high speed performance of the AD8036 and AD8037 requires careful attention to board layout and component selection. Proper RF design techniques and low pass parasitic component selection are mandatory. The PCB should have a ground plane ...
Page 22
AD8036/AD8037 ...
Page 23
OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 8-Lead Plastic DIP (N Package) 0.430 (10.92) 0.348 (8.84 0.280 (7.11) 0.240 (6.10 0.325 (8.25) PIN 1 0.100 (2.54) 0.300 (7.62) BSC 0.060 (1.52) 0.210 0.015 (0.38) (5.33) ...