OP97EPZ Analog Devices Inc, OP97EPZ Datasheet - Page 12

• Manufacturer Part Number: OP97EPZ
• Description: IC OPAMP GP LP PREC 8DIP
• Manufacturer: Analog Devices Inc

Specifications of OP97EPZ

• Slew Rate: 0.2 V/µs
• Amplifier Type: General Purpose
• Number Of Circuits: 1
• -3db Bandwidth: 900kHz
• Current - Input Bias: 30pA
• Voltage - Input Offset: 10µV
• Current - Supply: 380µA
• Voltage - Supply, Single/dual (±): ±2 V ~ 20 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Op Amp Type: Low Power
• No. Of Amplifiers: 1
• Bandwidth: 900kHz
• Supply Voltage Range: ± 2V To ± 20V
• Amplifier Case Style: DIP
• No. Of Pins: 8
• Common Mode Rejection Ratio: 132
• Current, Input Bias: ±30 pA
• Current, Input Offset: 30 pA
• Current, Supply: 380 μA
• Impedance, Thermal: 43 °C/W
• Package Type: PDIP-8
• Resistance, Input: 30 Megohms
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Gain: 2000 V/mV
• Voltage, Input: ±20 V
• Voltage, Noise: 17 nV/sqrt Hz
• Voltage, Offset: 10 μV
• Voltage, Output, High: +14 V
• Voltage, Output, Low: -14 V
• Voltage, Supply: ±15 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Current - Output / Channel: -
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

OP97
AC PERFORMANCE
The ac characteristics of the OP97 are highly stable over its full
operating temperature range. Unity-gain small-signal response
is shown in Figure 30. Extremely tolerant of capacitive loading
on the output, the OP97 displays excellent response even with
1000 pF loads (see Figure 31). In large signal applications, the
input protection diodes effectively short the input to the output
during the transients if the amplifier is connected in the usual
unity-gain configuration. The output enters short-circuit current
limit, with the flow going through the protection diodes.
Improved large signal transient response is obtained by using a
feedback resistor between the output and the inverting input.
Figure 32 shows the large-signal response of the OP97 in unity-
gain with a 10 kΩ feedback resistor. The unity-gain follower
circuit is shown in Figure 33.
The overcompensation pin (Pin 5) can be used to increase the
phase margin of the OP97 or to decrease gain bandwidth
product at gains greater than 10.
100
100
90
10
90
10
0%
0%
20mV
20mV
Figure 31. Small-Signal Transient Response
Figure 30. Small Signal Transient Response
(C
(C
LOAD
LOAD
= 1000 pF, A
= 100 pF, A
VCL
VCL
= 1)
= 1)
5µs
5µs
Rev. G | Page 12 of 16
Figure 34. Small Signal Transient Response with Overcompensation
100
100
90
10
90
10
0%
0%
Figure 32. Large Signal Transient Response (A
20mV
2V
V
IN
(C
LOAD
Figure 33. Unity-Gain Follower
= 1000 pF, A
2
3
OP97
10kΩ
VCL
= 1, C
6
OC
= 220 pF)
V
OUT
5µs
VCL
20µs
= 1)