AD8132ARMZ Analog Devices Inc, AD8132ARMZ Datasheet - Page 25

• Manufacturer Part Number: AD8132ARMZ
• Description: IC AMP DIFF LDIST LP 70MA 8MSOP
• Manufacturer: Analog Devices Inc
• Type: Differential Ampr

Specifications of AD8132ARMZ

• Amplifier Type: Differential
• Number Of Circuits: 1
• Output Type: Differential
• Slew Rate: 1200 V/µs
• -3db Bandwidth: 360MHz
• Current - Input Bias: 3µA
• Voltage - Input Offset: 1000µV
• Current - Supply: 12mA
• Current - Output / Channel: 70mA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 11 V, ±1.35 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Number Of Channels: 1
• Number Of Elements: 1
• Power Supply Requirement: Single/Dual
• Common Mode Rejection Ratio: 70dB
• Voltage Gain Db: 0.129dB
• Input Resistance: 3@5VMohm
• Input Offset Voltage: 3.5@5VmV
• Input Bias Current: 7@5VnA
• Single Supply Voltage (typ): 3/5/9V
• Dual Supply Voltage (typ): ±3/±5V
• Power Supply Rejection Ratio: 70dB
• Power Dissipation: 250mW
• Rail/rail I/o Type: No
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 11V
• Dual Supply Voltage (min): ±1.35V
• Dual Supply Voltage (max): ±5.5V
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: MSOP
• No. Of Amplifiers: 1
• Gain Db Max: 1.015dB
• Bandwidth: 350MHz
• Supply Voltage Range: ± 1.35V To ± 5.5V
• Supply Current: 10.7mA
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: Compliant

LAYOUT, GROUNDING, AND BYPASSING
As a high speed part, the AD8132 is sensitive to the printed
circuit board (PCB) environment in which it operates. Realizing
its superior specifications requires attention to various details of
good high speed PCB design.
The first requirement is a good solid ground plane that covers as
much of the board area around the AD8132 as possible. The only
exception to this is that the two input pins (Pin 1 and Pin 8) are
kept a few millimeters from the ground plane and that ground
be removed from inner layers and the opposite side of the board
under the input pins. This minimizes the stray capacitance on
these nodes and helps preserve the gain flatness vs. the frequency.
Bypass the power supply pins as close as possible to the device
to the nearby ground plane and use good high frequency ceramic
chip capacitors. Do this bypassing with a capacitance value
of 0.01 μF to 0.1 μF for each supply. Farther away, provide low
frequency bypassing with 10 μF tantalum capacitors from each
supply to ground.
Keep the signal routing short and direct to avoid parasitic effects.
Wherever there are complementary signals, a symmetrical
layout with matched lengths must be provided to the extent
possible to maximize the balance performance. When running
differential signals over a long distance, place the traces on
the PCB close together or twist together any differential wiring
to minimize the area of the loop that is formed. This reduces
the radiated energy and makes the circuit less susceptible to
interference.
Rev. I | Page 25 of 32
CIRCUITS
Figure 70. G = +2 Circuit with β1 = 0, Without Resistors
Figure 67. Typical Four-Resistor Feedback Circuit
Figure 68. Typical Circuit with β1 = 0
Figure 69. Typical Circuit with β2 = 1
Figure 71. Typical Circuit with β2 = 0
V
V
V
IN
IN
IN
R
R
R
R
G1
G1
G2
G2
R
G1
R
R
R
R
+
+
+
+
F1
F2
F2
F1
R
+
F1
AD8132