M37516F8HP Renesas Electronics America, M37516F8HP Datasheet - Page 26

• Manufacturer Part Number: M37516F8HP
• Description: IC 740 MCU FLASH 32K 48QFP
• Manufacturer: Renesas Electronics America
• Series: 740/38000r

Specifications of M37516F8HP

• Core Processor: 740
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SIO, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

7516 Group
Fig. 21 Operation of UART serial I/O1 function
[Transmit Buffer Register/Receive Buffer
Register (TB/RB)] 0018
The transmit buffer register and the receive buffer register are lo-
cated at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
[Serial I/O1 Status Register (SIOSTS)] 0019
The read-only serial I/O1 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O1
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer reg-
ister, and the receive buffer full flag is set. A write to the serial I/O1
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O1 enable bit SIOE
(bit 7 of the serial I/O1 control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O1 status register are initialized to “0” at
reset, but if the transmit enable bit (bit 4) of the serial I/O1 control
register has been set to “1”, the transmit shift completion flag (bit
2) and the transmit buffer empty flag (bit 0) become “1”.
Rev.1.01
Transmit or receive clock
Transmit buffer write
Receive buffer read
Serial output T
Notes
Serial input R
Jul 01, 2003
1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
3: The receive interrupt (RI) is set when the RBF flag becomes “1.”
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
signal
signal
interrupt source selection bit (TIC) of the serial I/O1 control register.
X
X
D
D
TBE=0
TSC=0
TBE=1
page 24 of 89
16
ST
ST
D
D
0
0
TBE=0
D
D
1
1
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
16
[Serial I/O1 Control Register (SIOCON)] 001A
The serial I/O1 control register consists of eight control bits for the
serial I/O1 function.
[UART Control Register (UARTCON)] 001B
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer and one bit (bit 4) which is al-
ways valid and sets the output structure of the P2
[Baud Rate Generator (BRG)] 001C
The baud rate generator determines the baud rate for serial trans-
fer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate genera-
tor.
RBF=1
SP
SP
TBE=1
ST
ST
D
0
D
0
RBF=0
D
D
1
1
Generated at 2nd bit in 2-stop-bit mode
5
/T
16
X
D pin.
TSC=1
SP
RBF=1
SP
16
16