ATMEGA164P-15MT Atmel, ATMEGA164P-15MT Datasheet - Page 325

• Manufacturer Part Number: ATMEGA164P-15MT
• Description: MCU AVR 16K FLASH 15MHZ 44-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA164P-15MT

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-VQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

25.10.14 Leaving Programming Mode
25.10.15 Performing Chip Erase
25.10.16 Programming the Flash
7674F–AVR–09/09
1. Enter JTAG instruction PROG_COMMANDS.
2. Disable all programming instructions by using no operation instruction 11a.
3. Enter instruction PROG_ENABLE and shift 0b0000_0000_0000_0000 in the program-
4. Enter JTAG instruction AVR_RESET and shift 0 in the Reset Register.
1. Enter JTAG instruction PROG_COMMANDS.
2. Start Chip Erase using programming instruction 1a.
3. Poll for Chip Erase complete using programming instruction 1b, or wait for t
Before programming the Flash a Chip Erase must be performed, see “Performing Chip Erase”
on page 325.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash write using programming instruction 2a.
3. Load address Extended High byte using programming instruction 2b.
4. Load address High byte using programming instruction 2c.
5. Load address Low byte using programming instruction 2d.
6. Load data using programming instructions 2e, 2f and 2g.
7. Repeat steps 5 and 6 for all instruction words in the page.
8. Write the page using programming instruction 2h.
9. Poll for Flash write complete using programming instruction 2i, or wait for t
10. Repeat steps 3 to 9 until all data have been programmed.
A more efficient data transfer can be achieved using the PROG_PAGELOAD instruction:
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash write using programming instruction 2a.
3. Load the page address using programming instructions 2b, 2c and 2d. PCWORD (refer
4. Enter JTAG instruction PROG_PAGELOAD.
5. Load the entire page by shifting in all instruction words in the page byte-by-byte, starting
6. Enter JTAG instruction PROG_COMMANDS.
7. Write the page using programming instruction 2h.
8. Poll for Flash write complete using programming instruction 2i, or wait for t
9. Repeat steps 3 to 8 until all data have been programmed.
ming Enable Register.
to
Table 25-14 on page
to
with the LSB of the first instruction in the page and ending with the MSB of the last
instruction in the page. Use Update-DR to copy the contents of the Flash Data Byte Reg-
ister into the Flash page location and to auto-increment the Program Counter before
each new word.
Table 25-14 on page
Table 25-14 on page
Table 25-7 on page
309).
309).
299) is used to address within one page and must be written as 0.
309).
ATmega164P/324P/644P
WLRH
WLRH
WLRH_CE
(refer to
(refer to
(refer
325