AT89C51ED2-3CSIM Atmel, AT89C51ED2-3CSIM Datasheet - Page 24
![IC 8051 MCU FLASH 64K 40DIP](/photos/6/70/67049/453-40-dip_sml.jpg)
AT89C51ED2-3CSIM
Manufacturer Part Number
AT89C51ED2-3CSIM
Description
IC 8051 MCU FLASH 64K 40DIP
Manufacturer
Atmel
Series
89Cr
Datasheet
1.ATWEBDVK-02RC.pdf
(137 pages)
Specifications of AT89C51ED2-3CSIM
Core Processor
8051
Core Size
8-Bit
Speed
60MHz
Connectivity
SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
34
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Data Bus Width
8 bit
Data Ram Size
64 KB
Interface Type
SPI, UART
Maximum Clock Frequency
60 MHz
Number Of Programmable I/os
32
Number Of Timers
3 x 16 bit
Operating Supply Voltage
2.7 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Data Converters
-
Lead Free Status / Rohs Status
No
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT89C51ED2-3CSIM
Manufacturer:
ATMEL
Quantity:
77 760
9.1
24
Registers
AT89C51RD2/ED2
The stack pointer (SP) may be located anywhere in the 256 bytes RAM (lower and upper RAM)
internal data memory. The stack may not be located in the XRAM.
The M0 bit allows to stretch the XRAM timings; if M0 is set, the read and write pulses are
extended from 6 to 30 clock periods. This is useful to access external slow peripherals.
Table 9-1.
AUXR - Auxiliary Register (8Eh)
• With EXTRAM = 0, the XRAM is indirectly addressed, using the MOVX instruction in
• With EXTRAM = 1, MOVX @Ri and MOVX @DPTR will be similar to the standard
Number
part of the available XRAM as explained in Table 9-1. This can be useful if external
peripherals are mapped at addresses already used by the internal XRAM.
combination with any of the registers R0, R1 of the selected bank or DPTR. An access to
XRAM will not affect ports P0, P2, P3.6 (WR) and P3.7 (RD). For example, with EXTRAM =
0, MOVX @R0, # data where R0 contains 0A0H, accesses the XRAM at address 0A0H
rather than external memory. An access to external data memory locations higher than the
accessible size of the XRAM will be performed with the MOVX DPTR instructions in the same
way as in the standard 80C51, with P0 and P2 as data/address busses, and P3.6 and P3.7
as write and read timing signals. Accesses to XRAM above 0FFH can only be done by the
use of DPTR.
80C51.MOVX @ Ri will provide an eight-bit address multiplexed with data on Port0 and any
output port pins can be used to output higher order address bits. This is to provide the
external paging capability. MOVX @DPTR will generate a sixteen-bit address. Port2 outputs
the high-order eight address bits (the contents of DPH) while Port0 multiplexes the low-order
eight address bits (DPL) with data. MOVX @ Ri and MOVX @DPTR will generate either read
or write signals on P3.6 (WR) and P3.7 (RD).
DPU
Bit
7
7
6
5
4
3
2
Mnemonic
AUXR Register
XRS2
XRS1
XRS0
DPU
Bit
M0
6
-
-
Description
Disable Weak Pull-up
Cleared by software to activate the permanent weak pull-up (default)
Set by software to disable the weak pull-up (reduce power consumption)
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Pulse length
Cleared to stretch MOVX control: the RD and the WR pulse length is 6 clock periods
(default).
Set to stretch MOVX control: the RD and the WR pulse length is 30 clock periods.
XRAM Size
XRS2XRS1XRS0 XRAM size
0
0
0
0
1
0
0
1
1
0
M0
5
0 256 bytes
1
0 768 bytes(default)
1 1024 bytes
0 1792 bytes
512 bytes
XRS2
4
XRS1
3
XRS0
2
EXTRAM
1
4235K–8051–05/08
AO
0