ATMEGA162-16PC Atmel, ATMEGA162-16PC Datasheet
ATMEGA162-16PC
Specifications of ATMEGA162-16PC
Related parts for ATMEGA162-16PC
ATMEGA162-16PC Summary of contents
Page 1
... ATmega162V – 2.4 - 4.0V for ATmega162U – 2.7 - 5.5V for ATmega162L – 4.5 - 5.5V for ATmega162 • Speed Grades – MHz for ATmega162V – MHz for ATmega162L/U – MHz for ATmega162 ® 8-bit Microcontroller 8-bit ATmega162 ATmega162V ATmega162U ATmega162L ...
Page 2
... Pin Configurations Disclaimer ATmega162(V/U/L) 2 Figure 1. Pinout ATmega162 (OC0/T0) PB0 (OC2/T1) PB1 (RXD1/AIN0) PB2 (TXD1/AIN1) PB3 (SS/OC3B) PB4 (MOSI) PB5 (MISO) PB6 (SCK) PB7 RESET (RXD0) PD0 (TXD0) PD1 (INT0/XCK1) PD2 (INT1/ICP3) PD3 (TOSC1/XCK0/OC3A) PD4 (OC1A/TOSC2) PD5 (WR) PD6 (RD) PD7 XTAL2 XTAL1 (MOSI) PB5 ...
Page 3
... Overview Block Diagram 2513CS–AVR–09/01 The ATmega162 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega162 achieves throughputs approaching 1 MIPS per MHz allowing the sys- tem designer to optimize power consumption versus processing speed. ...
Page 4
... ATmega161, all I/O locations present in ATmega161 have the same locations in ATmega162. Some additional I/O locations are added in an Extended I/O space starting from 0x60 to 0xFF, (i.e., in the ATmega162 internal RAM space). These locations can be reached by using LD/LDS/LDD and ST/STS/STD instructions only, not by using IN and OUT instructions ...
Page 5
... The Port A pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port A also serves the functions of various special features of the ATmega162 as listed on page 71. Port 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit) ...
Page 6
... The Port E pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port E also serves the functions of various special features of the ATmega162 as listed on page 80. Reset input. A low level on this pin for longer than the minimum pulse length will gener- ate a Reset, even if the clock is not running ...
Page 7
... ATmega162 Typical Characteristics – Preliminary Data 2513CS–AVR–09/01 The following charts show typical behavior. These figures are not tested during manu- facturing. All current consumption measurements are performed with all I/O pins configured as inputs and with internal pull-ups enabled. A sine wave generator with rail- to-rail output is used as clock source ...
Page 8
... Reserved – (0x66) Reserved – (0x65) Reserved – (0x64) Reserved – (0x63) Reserved – (0x62) Reserved – (0x61) CLKPR CLKPCE ATmega162(V/U/L) 8 Bit 6 Bit 5 Bit 4 Bit 3 – – – – – – – – – – – – – – – ...
Page 9
... ACO ACI ACIE – – – – – – – – – Oscillator Calibration Register On-chip Debug Register USART1 I/O Data Register TXC1 UDRE1 FE1 DOR1 ATmega162(V/U/L) Bit 2 Bit 1 Bit 0 – – – – SP10 SP9 SP8 SP2 SP1 SP0 UBRR1[11:8] ...
Page 10
... Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on all bits in the I/O Register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers 0x00 to 0x1F only. ATmega162(V/U/L) 10 Bit 6 ...
Page 11
... Branch if Half Carry Flag Set BRHC k Branch if Half Carry Flag Cleared BRTS k Branch if T Flag Set BRTC k Branch if T Flag Cleared BRVS k Branch if Overflow Flag is Set BRVC k Branch if Overflow Flag is Cleared 2513CS–AVR–09/01 ATmega162(V/U/L) Operation Flags Z,C,N,V Z,C,N,V,H Rdh:Rdl Rdh:Rdl + K Z,C,N,V Z,C,N,V ...
Page 12
... Set Signed Test Flag CLS Clear Signed Test Flag SEV Set Twos Complement Overflow. CLV Clear Twos Complement Overflow SET Set T in SREG CLT Clear T in SREG SEH Set Half Carry Flag in SREG ATmega162(V/U/L) 12 Operation Flags then None then None Rd Rr None ...
Page 13
... Clear Half Carry Flag in SREG CLH MCU CONTROL INSTRUCTIONS NOP No Operation SLEEP Sleep WDR Watchdog Reset BREAK Break 2513CS–AVR–09/01 ATmega162(V/U/L) Operation Flags None (see specific descr. for Sleep function) None (see specific descr. for WDR/Timer) None For On-chip Debug Only ...
Page 14
... ATmega162V-1MC 44M1 ATmega162U-8AC 44A ATmega162U-8PC 40P6 ATmega162U-8MC 44M1 ATmega162L-8AC 44A ATmega162L-8PC 40P6 ATmega162L-8MC 44M1 ATmega162L-8AI 44A ATmega162L-8PI 40P6 ATmega162L-8MI 44M1 ATmega162-16AC 44A ATmega162-16PC 40P6 ATmega162-16MC 44M1 ATmega162-16AI 44A ATmega162-16PI 40P6 ATmega162-16MI 44M1 Package Type Operation Range Commercial Commercial Commercial Industrial ...
Page 15
... Dimension in Millimeters and (Inches)* JEDEC STANDARD MS-026 ACB 0.80(0.0315) BSC 0.20(0.008) 0.09(0.004) REV. A 04/11/2001 2513CS–AVR–09/01 PIN 1 ID PIN 1 0˚~7˚ 0.75(0.030) 0.45(0.018) *Controlling dimension: millimeter ATmega162(V/U/L) 12.25(0.482) SQ 11.75(0.462) 0.45(0.018) 0.30(0.012) 10.10(0.394) SQ 9.90(0.386) 1.20(0.047) MAX 0.15(0.006) 0.05(0.002) 15 ...
Page 16
... Plastic Dual Inline Package (PDIP), 0.600" wide Dimension in Millimeters and (Inches)* JEDEC STANDARD MS-011 AC 4.83(0.190)MAX SEATING PLANE 3.56(0.140) 3.05(0.120) 2.54(0.100)BSC 0.38(0.015) 0.20(0.008) REV. A 04/11/2001 ATmega162(V/U/L) 16 52.71(2.075) 51.94(2.045) 48.26(1.900) REF 1.65(0.065) 1.27(0.050) 15.88(0.625) 15.24(0.600) 0º ~ 15º 17.78(0.700)MAX *Controlling dimension: Inches PIN 1 13 ...
Page 17
... NOTE 1. JEDEC STANDARD MO-220, Fig 1 (Saw Singulation), VKKD-1 2325 Orchard Parkway San Jose, CA 95131 R 2513CS–AVR–09/ PIN #1 CORNER D2 e TITLE 44M1, 44-pad , 1.0 mm body, lead pitch 0.50mm Micro lead frame package (MLF) ATmega162(V/U/ SIDE VIEW COMMON DIMENSIONS (*Unit of Measure = mm) NOTE SYMBOL MIN NOM MAX A ...
Page 18
... The referring revision in this section are referring to the document revision. 1. Added information for ATmega162U. Information about ATmega162U included in “Features” on page 1, Table 19, “BODLEVEL Fuse Coding,” on page 49, and “Ordering Information” on page 14. 1. Canged the Endurance on the Flash to 10,000 Write/Erase Cycles. ...
Page 19
... No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ...