ATMEGA32-16PC Atmel, ATMEGA32-16PC Datasheet - Page 271

• Manufacturer Part Number: ATMEGA32-16PC
• Description: IC AVR MCU 32K 16MHZ COM 40-DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32-16PC

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

SPI Serial
Programming
Algorithm
Data Polling Flash
2503Q–AVR–02/11
tion. The Chip Erase operation turns the content of every memory location in both the Program
and EEPROM arrays into $FF.
Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low:> 2 CPU clock cycles for f
High:> 2 CPU clock cycles for f
When writing serial data to the ATmega32, data is clocked on the rising edge of SCK.
When reading data from the ATmega32, data is clocked on the falling edge of SCK. See
137
To program and verify the ATmega32 in the SPI Serial Programming mode, the following
sequence is recommended (See four byte instruction formats in
1. Power-up sequence:
2. Wait for at least 20ms and enable SPI Serial Programming by sending the Programming
3. The SPI Serial Programming instructions will not work if the communication is out of syn-
4. The Flash is programmed one page at a time (page size found in
5. The EEPROM array is programmed one byte at a time by supplying the address and data
6. Any memory location can be verified by using the Read instruction which returns the con-
7. At the end of the programming session, RESET can be set high to commence normal
8. Power-off sequence (if needed):
When a page is being programmed into the Flash, reading an address location within the page
being programmed will give the value $FF. At the time the device is ready for a new page, the
programmed value will read correctly. This is used to determine when the next page can be writ-
Apply power between V
tems, the programmer can not guarantee that SCK is held low during power-up. In this
case, RESET must be given a positive pulse of at least two CPU clock cycles duration
after SCK has been set to “0”.
Enable serial instruction to pin MOSI.
chronization. When in sync. the second byte ($53), will echo back when issuing the third
byte of the Programming Enable instruction. Whether the echo is correct or not, all four
bytes of the instruction must be transmitted. If the $53 did not echo back, give RESET a
positive pulse and issue a new Programming Enable command.
258). The memory page is loaded one byte at a time by supplying the 6LSB of the
address and data together with the Load Program Memory Page instruction. To ensure
correct loading of the page, the data low byte must be loaded before data high byte is
applied for a given address. The Program Memory Page is stored by loading the Write
Program Memory Page instruction with the 8MSB of the address. If polling is not used,
the user must wait at least t
Accessing the SPI Serial Programming interface before the Flash write operation com-
pletes can result in incorrect programming.
together with the appropriate Write instruction. An EEPROM memory location is first
automatically erased before new data is written. If polling is not used, the user must wait
at least t
no $FFs in the data file(s) need to be programmed.
tent at the selected address at serial output MISO.
operation.
Set RESET to “1”.
Turn V
for timing details.
CC
WD_EEPROM
power off.
before issuing the next byte. (See
CC
ck
and GND while RESET and SCK are set to “0”. In some sys-
ck
WD_FLASH
< 12MHz, 3 CPU clock cycles for f
< 12MHz, 3 CPU clock cycles for f
before issuing the next page. (See
Table
114). In a chip erased device,
Table
ck
ck
≥ 12MHz
“Page Size” on page
≥ 12MHz
ATmega32(L)
115):
Table
114).
Figure
271