T89C51RD2-SLSIM Atmel, T89C51RD2-SLSIM Datasheet - Page 35
![IC MICRO CTRL 64K FLASH 44PLCC](/photos/6/70/67043/453-44-plcc_sml.jpg)
T89C51RD2-SLSIM
Manufacturer Part Number
T89C51RD2-SLSIM
Description
IC MICRO CTRL 64K FLASH 44PLCC
Manufacturer
Atmel
Series
89Cr
Datasheet
1.T89C51RD2-SMSIM.pdf
(104 pages)
Specifications of T89C51RD2-SLSIM
Core Processor
8051
Core Size
8-Bit
Speed
40MHz
Connectivity
SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
32
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Data Converters
-
Broadcast Address
Reset Addresses
4243G–8051–05/03
The SADEN byte is selected so that each slave may be addressed separately.
For slave A, bit 0 (the LSB) is a don’t-care bit; for slaves B and C, bit 0 is a 1. To com-
municate with slave A only, the master must send an address where bit 0 is clear (e.g.
1111 0000b ).
For slave A, bit 1 is a 1; for slaves B and C, bit 1 is a don’t care bit. To communicate with
slaves B and C, but not slave A, the master must send an address with bits 0 and 1 both
set (e.g. 1111 0011b ).
To communicate with slaves A, B and C, the master must send an address with bit 0
set, bit 1 clear, and bit 2 clear (e.g. 1111 0001b ).
A broadcast address is formed from the logical OR of the SADDR and SADEN registers
with zeros defined as don’t-care bits, e.g.:
The use of don’t-care bits provides flexibility in defining the broadcast address, however
in most applications, a broadcast address is FFh. The following is an example of using
broadcast addresses:
For slaves A and B, bit 2 is a don’t care bit; for slave C, bit 2 is set. To communicate with
all of the slaves, the master must send an address FFh. To communicate with slaves A
and B, but not slave C, the master can send and address FBh.
On reset, the SADDR and SADEN registers are initialized to 00h, i.e. the given and
broadcast addresses are XXXX XXXXb (all don’t-care bits). This ensures that the serial
port will reply to any address, and so, that it is backwards compatible with the 80C51
microcontrollers that do not support automatic address recognition.
Table 18. SADEN - Slave Address Mask Register (B9h)
Reset Value = 0000 0000b
Not bit addressable
Slave A:SADDR1111 0001b
Slave B:SADDR1111 0011b
Slave C:SADDR=1111 0010b
7
Broadcast =SADDR OR SADEN1111 111Xb
SADDR 0101 0110b
SADEN 1111 1100b
SADEN1111 1010b
Broadcast1111 1X11b,
SADEN1111 1001b
Broadcast1111 1X11B,
SADEN1111 1101b
Broadcast1111 1111b
6
5
4
3
2
T89C51RD2
1
0
35