PIC16C72-10E/SS Microchip Technology, PIC16C72-10E/SS Datasheet - Page 60
![IC MCU OTP 2KX14 A/D PWM 28SSOP](/photos/6/81/68119/150-28-ssop_sml.jpg)
PIC16C72-10E/SS
Manufacturer Part Number
PIC16C72-10E/SS
Description
IC MCU OTP 2KX14 A/D PWM 28SSOP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16C72-04SO.pdf
(289 pages)
4.PIC16C72-04SO.pdf
(125 pages)
5.PIC16C72-04SO.pdf
(8 pages)
Specifications of PIC16C72-10E/SS
Core Processor
PIC
Core Size
8-Bit
Speed
10MHz
Connectivity
I²C, SPI
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Size
3.5KB (2K x 14)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 5x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
28-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
PIC16C72 Series
10.2
10.2.1
The PIC16CXXX family can be operated in four differ-
ent oscillator modes. The user can program two config-
uration bits (FOSC1 and FOSC0) to select one of these
four modes:
• LP
• XT
• HS
• RC
10.2.2
In XT, LP or HS modes a crystal or ceramic resonator
is connected to the OSC1/CLKIN and OSC2/CLKOUT
pins
PIC16CXXX family oscillator design requires the use of
a parallel cut crystal. Use of a series cut crystal may
give a frequency out of the crystal manufacturers spec-
ifications. When in XT, LP or HS modes, the device can
have an external clock source to drive the OSC1/
CLKIN pin (Figure 10-3).
FIGURE 10-2: CRYSTAL/CERAMIC
FIGURE 10-3: EXTERNAL CLOCK INPUT
DS39016A-page 60
Note1:
Clock from
ext. system
to
2:
3:
C1
C2
Oscillator Configurations
CRYSTAL OSCILLATOR/CERAMIC
RESONATORS
OSCILLATOR TYPES
(1)
(1)
establish
Low Power Crystal
Crystal/Resonator
High Speed Crystal/Resonator
Resistor/Capacitor
See Table 10-1 and Table 10-2 for recom-
mended values of C1 and C2.
A series resistor (RS) may be required for
AT strip cut crystals.
RF varies with the crystal chosen.
XTAL
RS
Open
(2)
RESONATOR OPERATION
(HS, XT OR LP
OSC CONFIGURATION)
OPERATION (HS, XT OR LP
OSC CONFIGURATION)
OSC1
OSC2
oscillation
OSC1
OSC2
RF
(3)
(Figure 10-2). The
PIC16CXXX
SLEEP
PIC16CXXX
To
internal
logic
Preliminary
TABLE 10-1
TABLE 10-2
Ranges Tested:
XT
HS
Resonators Used:
455 kHz
2.0 MHz
4.0 MHz
8.0 MHz
16.0 MHz Murata Erie CSA16.00MX
Note 1: Recommended values of C1 and C2 are
Osc Type
Mode
200 kHz
20 MHz
32 kHz
1 MHz
4 MHz
8 MHz
All resonators used did not have built-in capacitors.
HS
LP
XT
2: Higher capacitance increases the stability
3: Since each resonator/crystal has its own
4: Rs may be required in HS mode as well as
These values are for design guidance only. See
notes at bottom of page.
These values are for design guidance only. See
notes at bottom of page.
identical to the ranges tested (Table 10-1).
of oscillator but also increases the start-up
time.
characteristics, the user should consult the
resonator/crystal manufacturer for appropri-
ate values of external components.
XT mode to avoid overdriving crystals with
low drive level specification.
455 kHz
2.0 MHz
4.0 MHz
8.0 MHz
16.0 MHz
Panasonic EFO-A455K04B
Murata Erie CSA2.00MG
Murata Erie CSA4.00MG
Murata Erie CSA8.00MT
Epson C-001R32.768K-A
STD XTL 200.000KHz
ECS ECS-10-13-1
ECS ECS-40-20-1
EPSON CA-301 8.000M-C
EPSON CA-301 20.000M-C
200 kHz
200 kHz
Freq
20 MHz
Crystal
32 kHz
1 MHz
4 MHz
4 MHz
8 MHz
Freq
CERAMIC RESONATORS
CAPACITOR SELECTION
FOR CRYSTAL OSCILLATOR
Crystals Used
1998 Microchip Technology Inc.
68 - 100 pF
15 - 68 pF
15 - 68 pF
10 - 68 pF
10 - 22 pF
Cap. Range
47-68 pF
15-33 pF
15-33 pF
OSC1
33 pF
15 pF
15 pF
15 pF
15 pF
C1
68 - 100 pF
15 - 68 pF
15 - 68 pF
10 - 68 pF
10 - 22 pF
Cap. Range
47-68 pF
15-33 pF
15-33 pF
0.3%
0.5%
0.5%
0.5%
0.5%
OSC2
20 PPM
20 PPM
50 PPM
50 PPM
30 PPM
30 PPM
33 pF
15 pF
15 pF
15 pF
15 pF
C2