PIC16C662-10/PQ Microchip Technology, PIC16C662-10/PQ Datasheet - Page 51
![IC MCU OTP 4KX14 COMP 44-MQFP](/photos/6/59/65984/150-44-pqfp_sml.jpg)
PIC16C662-10/PQ
Manufacturer Part Number
PIC16C662-10/PQ
Description
IC MCU OTP 4KX14 COMP 44-MQFP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Specifications of PIC16C662-10/PQ
Core Processor
PIC
Core Size
8-Bit
Speed
10MHz
Peripherals
Brown-out Detect/Reset, LED, POR, WDT
Number Of I /o
33
Program Memory Size
7KB (4K x 14)
Program Memory Type
OTP
Ram Size
176 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Oscillator Type
External
Operating Temperature
0°C ~ 70°C
Package / Case
44-MQFP, 44-PQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Connectivity
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16C662-10/PQ
Manufacturer:
Microchip Technology
Quantity:
10 000
7.6
The comparator interrupt flag is set whenever there is
a change in the output value of either comparator. User
software will need to maintain information about the
status of the output bits, as read from CMCON<7:6>, to
determine the actual change that has occurred. The
CMIF bit (PIR1<6>), is the comparator interrupt flag
and must be cleared in user software.
To enable the Comparator interrupt the following bits
must be set:
• CMIE (PIE1<6>)
• PEIE (INTCON<6>)
• GIE (INTCON<7>)
The user, in the interrupt service routine, can clear the
interrupt in the following manner:
a)
b)
A mismatch condition will continue to set flag bit CMIF.
Reading CMCON will end the mismatch condition, and
allow flag bit CMIF to be cleared.
7.7
When a comparator is active and the device is placed
in SLEEP mode, the comparator remains active and
the interrupt is functional if enabled. This interrupt will
wake up the device from SLEEP mode when enabled.
While the comparator is powered up, higher sleep
currents than shown in the power-down current
specification will occur. Each comparator that is
operational will consume additional current as shown in
the comparator specifications. To minimize power
consumption while in SLEEP mode, turn off the
FIGURE 7-5:
1996 Microchip Technology Inc.
Any read or write of CMCON. This will end the
mismatch condition.
Clear flag bit CMIF.
Comparator Interrupts
Comparator Operation During SLEEP
V
Legend C
A
ANALOG INPUT MODEL
R
S
V
I
R
R
V
LEAKAGE
T
A
PIN
IC
S
A
IN
5 pF
C
PIN
= Input Capacitance
= Threshold Voltage
= Leakage Current at the pin due to various junctions
= Interconnect Resistance
= Source Impedance
= Analog Voltage
Preliminary
PIC16C64X & PIC16C66X
V
DD
V
V
T
T
= 0.6V
= 0.6V
comparators, CM2:CM0 = 111, before entering sleep.
If the device wakes up from sleep, the contents of the
CMCON register are not affected.
7.8
A device reset forces the CMCON register to its reset
state. This forces the comparator module to be in the
comparator
ensures that all potential inputs are analog inputs.
Device current is minimized when analog inputs are
present at reset time. The comparators will be powered
down during the reset interval.
7.9
A simplified circuit for an analog input is shown in
Figure 7-5. Since the analog pins are connected to a
digital output, they have reverse biased diodes to V
and V
V
range by more than 0.6V in either direction, one of the
diodes is forward biased and a latch-up may occur. A
maximum
recommended for the analog sources. Any external
component connected to an analog input pin, such as
a capacitor or a Zener diode, should have very little
leakage current.
SS
and V
SS
. The analog input therefore, must be between
Effects of a RESET
Analog Input Connection
Considerations
I
V
LEAKAGE
DD
500 nA
SS
source
. If the input voltage deviates from this
reset
R
C
< 10k
mode,
impedance
CM2:CM0 = 000.
DS30559A-page 51
of
10 k
This
DD
is