AT90S8515-8PC Atmel, AT90S8515-8PC Datasheet - Page 55

• Manufacturer Part Number: AT90S8515-8PC
• Description: IC MCU 8K FLSH 8MHZ 40DIP
• Manufacturer: Atmel
• Series: AVR® 90Sr

Specifications of AT90S8515-8PC

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Data Converters: -

UART Control
UART I/O Data Register – UDR
UART Status Register – USR
0841G–09/01
The UDR register is actually two physically separate registers sharing the same I/O
address. When writing to the register, the UART Transmit Data register is written. When
reading from UDR, the UART Receive Data register is read.
The USR register is a read-only register providing information on the UART status.
• Bit 7 – RXC: UART Receive Complete
This bit is set (one) when a received character is transferred from the Receiver Shift reg-
ister to UDR. The bit is set regardless of any detected framing errors. When the RXCIE
bit in UCR is set, the UART Receive Complete interrupt will be executed when RXC is
set (one). RXC is cleared by reading UDR. When interrupt-driven data reception is used,
the UART Receive Complete Interrupt routine must read UDR in order to clear RXC,
otherwise a new interrupt will occur once the interrupt routine terminates.
• Bit 6 – TXC: UART Transmit Complete
This bit is set (one) when the entire character (including the stop bit) in the Transmit
Shift register has been shifted out and no new data has been written to UDR. This flag is
especially useful in half-duplex communications interfaces, where a transmitting appli-
cation must enter receive mode and free the communications bus immediately after
completing the transmission.
When the TXCIE bit in UCR is set, setting of TXC causes the UART Transmit Complete
interrupt to be executed. TXC is cleared by hardware when executing the corresponding
interrupt handling vector. Alternatively, the TXC bit is cleared (zero) by writing a logical
“1” to the bit.
• Bit 5 – UDRE: UART Data Register Empty
This bit is set (one) when a character written to UDR is transferred to the Transmit Shift
register. Setting of this bit indicates that the transmitter is ready to receive a new charac-
ter for transmission.
When the UDRIE bit in UCR is set, the UART Transmit Complete interrupt to be exe-
cuted as long as UDRE is set. UDRE is cleared by writing UDR. When interrupt-driven
data transmittal is used, the UART Data Register Empty Interrupt routine must write
UDR in order to clear UDRE, otherwise a new interrupt will occur once the interrupt rou-
tine terminates.
UDRE is set (one) during reset to indicate that the transmitter is ready.
• Bit 4 – FE: Framing Error
This bit is set if a Framing Error condition is detected, i.e., when the stop bit of an incom-
ing character is zero.
Bit
$0C ($2C)
Read/Write
Initial Value
Bit
$0B ($2B)
Read/Write
Initial Value
MSB
RXC
R/W
R
7
0
7
0
TXC
R/W
R/W
6
0
6
0
UDRE
R/W
R
5
0
5
1
R/W
FE
R
4
0
4
0
R/W
OR
R
3
0
3
0
R/W
R
2
0
2
–
0
R/W
R
1
0
1
–
0
AT90S8515
LSB
R/W
R
0
0
0
–
0
UDR
USR
55