PIC17LC756-08I/L Microchip Technology, PIC17LC756-08I/L Datasheet - Page 239

• Manufacturer Part Number: PIC17LC756-08I/L
• Description: MICRO CTRL 16K LOW PWR 68PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17LC756-08I/L

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: OTP
• Ram Size: 902 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 68-PLCC
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -

20.0
Absolute Maximum Ratings †
Ambient temperature under bias.............................................................................................................-55°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on V
Voltage on MCLR with respect to V
Voltage on RA2 and RA3 with respect to V
Voltage on all other pins with respect to V
Total power dissipation (Note 1) ..............................................................................................................................1.0 W
Maximum current out of V
Maximum current into V
Input clamp current, I
Output clamp current, I
Maximum output current sunk by any I/O pin (except RA2 and RA3).....................................................................35 mA
Maximum output current sunk by RA2 or RA3 pins ................................................................................................60 mA
Maximum output current sourced by any I/O pin ....................................................................................................20 mA
Maximum current sunk by PORTA and PORTB (combined).................................................................................150 mA
Maximum current sourced by PORTA and PORTB (combined) ...........................................................................100 mA
Maximum current sunk by PORTC, PORTD and PORTE (combined)..................................................................150 mA
Maximum current sourced by PORTC, PORTD and PORTE (combined) ............................................................100 mA
Maximum current sunk by PORTF and PORTG (combined) ................................................................................150 mA
Maximum current sourced by PORTF and PORTG (combined)...........................................................................100 mA
Maximum current sunk by PORTH and PORTJ (combined).................................................................................150 mA
Maximum current sourced by PORTH and PORTJ (combined) ...........................................................................100 mA
† NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent dam-
age to the device. This is a stress rating only and functional operation of the device at those or any other
conditions above those indicated in the operation listings of this specification is not implied. Exposure to
maximum rating conditions for extended periods may affect device reliability.
2000 Microchip Technology Inc.
Note 1: Power dissipation is calculated as follows: Pdis = V
2: Voltage spikes below V
PIC17C7XX ELECTRICAL CHARACTERISTICS
Thus, a series resistor of 50-100
pulling this pin directly to V
DD
with respect to V
IK
OK
(V
DD
SS
I
(V
< 0 or V
pin(s) - total (@ 70°C) ...............................................................................................500 mA
O
pin(s) - total (@ 70°C) ............................................................................................500 mA
< 0 or V
SS
I
SS
SS
> V
........................................................................................................... 0 V to +7.5 V
O
SS
(Note 2) ....................................................................................... -0.3 V to +14 V
at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.
DD
> V
.
SS
) .......................................................................................................... ±20 mA
SS
DD
...................................................................................-0.3 V to V
.......................................................................................... -0.3 V to +8.5 V
) ...................................................................................................±20 mA
should be used when applying a "low" level to the MCLR pin, rather than
DD
x {I
DD
-
I
OH
} +
{(V
PIC17C7XX
DD
-V
OH
) x I
DS30289B-page 239
OH
} + (V
DD
OL
+ 0.3 V
x I
OL
)