SAK-XC164CS-32F20F BB-A Infineon Technologies, SAK-XC164CS-32F20F BB-A Datasheet - Page 31

• Manufacturer Part Number: SAK-XC164CS-32F20F BB-A
• Description: IC MCU 16BIT 256KB FLASH 100TQFP
• Manufacturer: Infineon Technologies
• Series: XC16xr

Specifications of SAK-XC164CS-32F20F BB-A

• Core Processor: C166SV2
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, EBI/EMI, SPI, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 79
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.7 V
• Data Converters: A/D 14x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-LFQFP
• Packages: PG-TQFP-100
• Max Clock Frequency: 20.0 MHz
• Sram (incl. Cache): 12.0 KByte
• Can Nodes: 2
• A / D Input Lines (incl. Fadc): 14
• Program Memory: 256.0 KByte
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: SP000224594

3.6
The CAPCOM units support generation and control of timing sequences on up to
32 channels with a maximum resolution of 1 system clock cycle (8 cycles in staggered
mode). The CAPCOM units are typically used to handle high speed I/O tasks such as
pulse and waveform generation, pulse width modulation (PMW), Digital to Analog (D/A)
conversion, software timing, or time recording relative to external events.
Four 16-bit timers (T0/T1, T7/T8) with reload registers provide two independent time
bases for each capture/compare register array.
The input clock for the timers is programmable to several prescaled values of the internal
system clock, or may be derived from an overflow/underflow of timer T6 in module GPT2.
This provides a wide range of variation for the timer period and resolution and allows
precise adjustments to the application specific requirements. In addition, external count
inputs for CAPCOM timers T0 and T7 allow event scheduling for the capture/compare
registers relative to external events.
Both of the two capture/compare register arrays contain 16 dual purpose
capture/compare registers, each of which may be individually allocated to either
CAPCOM timer T0 or T1 (T7 or T8, respectively), and programmed for capture or
compare function.
12 registers of the CAPCOM2 module have each one port pin associated with it which
serves as an input pin for triggering the capture function, or as an output pin to indicate
the occurrence of a compare event.
Table 6
Compare Modes
Mode 0
Mode 1
Mode 2
Mode 3
Double Register
Mode
Single Event Mode
Data Sheet
Capture/Compare Units (CAPCOM1/2)
Compare Modes (CAPCOM1/2)
Function
Interrupt-only compare mode;
several compare interrupts per timer period are possible
Pin toggles on each compare match;
several compare events per timer period are possible
Interrupt-only compare mode;
only one compare interrupt per timer period is generated
Pin set ‘1’ on match; pin reset ‘0’ on compare timer overflow;
only one compare event per timer period is generated
Two registers operate on one pin;
pin toggles on each compare match;
several compare events per timer period are possible
Generates single edges or pulses;
can be used with any compare mode
29
Functional Description
Derivatives
V1.1, 2006-08
XC164-32