M30835FJGP#U5 Renesas Electronics America, M30835FJGP#U5 Datasheet - Page 22

• Manufacturer Part Number: M30835FJGP#U5
• Description: IC M32C/83 MCU FLASH 144LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M32C/80r

Specifications of M30835FJGP#U5

• Core Processor: M32C/80
• Core Size: 16/32-Bit
• Speed: 32MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 121
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 31K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 34x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 144-LQFP
• For Use With: R0K330879S001BE - KIT DEV RSK M32C/87R0K330879S000BE - KIT DEV RSK M32C/87
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R
R
M
e
E
2.2 High-Speed Interrupt Registers
2.3 DMAC-Associated Registers
3
. v
J
2
0
1
C
3
4 .
B
8 /
Registers associated with the high-speed interrupt are as follows. Refer to 10.4 High-Speed Interrupt for
details.
Registers associated with DMAC are as follows. Refer to 12. DMAC for details.
- Flag save register (SVF)
- PC save register (SVP)
- Vector register (VCT)
- DMA mode register (DMD0, DMD1)
- DMA transfer count register (DCT0, DCT1)
- DMA transfer count reload register (DRC0, DRC1)
- DMA memory address register (DMA0, DMA1)
- DMA SFR address register (DSA0, DSA1)
- DMA memory address reload register (DRA0, DRA1)
0
1
2.1.8.5 Register Bank Select Flag (B)
2.1.8.6 Overflow Flag (O)
2.1.8.7 Interrupt Enable Flag (I)
2.1.8.8 Stack Pointer Select Flag (U)
2.1.8.9 Processor Interrupt Priority Level (IPL)
2.1.8.10 Reserved Space
3
0
1
The register bank 0 is selected when the B flag is set to "0". The register bank 1 is selected when this
flag is set to "1".
The O flag is set to "1" when the result of an arithmetic operation overflows; otherwise "0".
The I flag enables a maskable interrupt.
An interrupt is disabled when the I flag is set to "0" and enabled when the I flag is set to "1". The I flag
is set to "0" when an interrupt is acknowledged.
ISP is selected when the U flag is set to "0". USP is selected when this flag is set to "1".
The U flag is set to "0" when a hardware interrupt is acknowledged or the INT instruction of software
interrupt numbers 0 to 31 is executed.
IPL, 3 bits wide, assigns processor interrupt priority levels from level 0 to level 7.
If a requested interrupt has greater priority than IPL, the interrupt is enabled.
When writing to a reserved space, set to "0". When read, its content is indeterminate.
J
G
3
a
0 -
o r
n
3 .
1
u
, 1
4
p
1
(
2
M
0
0
3
6
2
C
8 /
Page 20
, 3
M
3
2
C
f o
8 /
9
3
1
) T